SCSI-1定义了一种具有5MHz数据时钟的8-bit并行接口,能提供最高 5 兆字节每秒(5MB/s)的数据传输速率。
SCSI-1 defined an 8-bit parallel interface with a 5MHz data clock, providing a maximum data transfer rate of 5 megabytes per second (MB/s).
它提供一个数据时钟输出(DCO)用于在输出端捕获数据,以及一个帧时钟输出(FCO)用于发送新输出字节信号。
A data clock output (DCO) for capturing data on the output and a frame clock output (FCO) for signaling a new output byte are provided.
这就是移位寄存器,因为数据在每一个时钟脉冲的作用下通过寄存器会移动一位。
It is called a shift register because the data is shifted through the register by one bit position on each clock pulse.
有一个预定义的变量 total_time,它代表整个数据收集过程的时钟时间。
You have a pre-defined variable named total_time for the wall-clock time of the whole data collection.
数据库存储过程和触发器中的处理将使用数据库时钟。
Processing moved into stored procedures and triggers within the database will use the database clock.
数据和时钟线都是集电极开路的。
预处理器主要有延迟单元、乘法器和窄带滤波电路构成,可以从NRZ数据中得到时钟信号。
The preprocessor can extract clock information from NRZ data stream, which consists of a delay cell, a multiplier and a narrow-band filter.
在突发式的接收模块中,逻辑电平的恢复和时钟数据的恢复是其关键的问题。
The most difficult problem in burst mode receiver would be signal logic level recovery and data and clock recovery.
可以预计,只要在器件上作某些更换,亦可制成工作速率更高的时钟数据恢复模块。
It is estimated that a data and clock recovery module with a higher operating rate is available only if some devices are changed.
着重阐述了软件设计中数据采集、显示、存储、时钟控制、RS485通信的编程思路。
It emphasized the programming thoughts of data collection, display, storage, clock control and RS485 communication in software design.
对于数据和时钟脉冲列之间的相关延迟的模拟,以0.1微秒为递增单位增加到3.1微秒。
Simulation of relative delays between Data and Clock pulse trains in 0.1 microseconds increments to 3.1 microseconds.
在二进制位同步通信中,使用时钟脉冲来控制数据和控制字符的同步。
In binary synchronous communication, the use of clock pulses to control synchronization of data and control characters.
论文中还给出了开关量输入、开关量输出、通信模块、时钟电路、数据存储器、按键电路和频率跟踪电路等各功能模块的选择方法和设计原理。
And the selection and design of switch-in module, switch-out module, communication module, clock module, data storage module, keys module and frequency detecting module are also discussed.
在串并转换接收器中,并行数据在字节时钟的作用下并行输出。
In the deserializer, parallel data are clocked out by byte clock.
如果不是,主机禁止通信,设备必须缓冲任何要发送的数据,直到主机释放时钟。
If it's not, the host is inhibiting communication and the device must buffer any to-be-sent data until the host releases Clock.
采用软件模拟时序使CPU的I/O口模拟I2C总线,实现了单片机与时钟芯片、温湿度传感器、存储芯片等器件的数据交换。
With time series simulation software, the CPU's I/O ports simulate I2C bus and exchange data with clock chips, temperature humidity sensors, memory chips and other devices.
CL是指“CAS延迟”,是指收到命令以后,再数据开始传输以前,所需要的时钟周期的数量。
Cl stands for "CAS latency," which is the number of clock cycles it takes before data starts to flow once a command is received.
在区域火灾报警控制器中,FM 31256芯片的非易失性数据存储器、实时时钟、看门狗等功能,增强系统可靠性。
The nonvolatile data memory, real-time clock, and watchdog functions of FM31256 chip were adopted by region fire alarm and control device to improve the system reliability.
随着采样频率和A/D变换器位数的增加,时钟抖动和相位噪声对数据采集系统性能的影响更加显著。
The effect of clock jitter and phase noise on data acquisition system performance is more profound as the increase of sampling frequency and the bit of A/D converter.
数据从主机发给从机可能会使用与从机发给主机相反的时钟沿。
Sending data from slave to master may use the opposite clock edge as master to slave.
转换过程和数据采集过程通过CS和串行时钟信号进行控制,从而为器件与微处理器或DSP轻松接口创造了条件。
The conversion process and data acquisition are controlled using CS and the serial clock signal, allowing the device to easily interface with microprocessors or DSPs.
转换过程和数据采集过程通过CS和串行时钟进行控制,从而为器件与微处理器或DSP接口创造了条件。
The conversion process and data acquisition are controlled using CS and the serial clock, allowing the devices to interface with microprocessors or DSPs.
时标输出除有常规的时、分和秒号外,还将日历和时钟数据以串行编码方式输出。
The clock and calendar data are also given in series code format as well as the normal output of hour, minute and second time marks.
在串行数据输入(DI)或输出(DO)时使用的时钟信号。
Used as the synchronization clock when inputting (DI) or outputting (DO)serial data.
该内核结构采用数据融合加强对精度要求较高的时钟同步任务的支持。
A kernel structure is presented, which adopts data fusion to support precision-demanding clock synchronization tasks.
以GPS系统实时时钟为基础,通过对绝对时标加以处理,以无线方式实现了不同站点之间的实时数据采集。
Based on real time clock of GPS system, and by means of absolute time-marker, real time data acquisition between different sites was performed in the form of wireless.
协议能有效解决数据边界识别问题和时钟累积误差造成的相位偏差问题。
The communication protocol could solve the issue of identifying the data boundaries and the phase error caused by the accumulated error of clock.
对于厂站层,论文提出了对不良数据分级处理和建立全网统一时钟的策略和方法。
For substation layer, a feasible strategy for bad data grading handling and a practicable method to establish the uniform clock for the power network were put forward.
后者为屏上驱动电路提供控制、时钟信号,完成视频数据的处理。
The latter provides the control and clock signals for the driving circuitry on screen and accomplishes the video data processing.
后者为屏上驱动电路提供控制、时钟信号,完成视频数据的处理。
The latter provides the control and clock signals for the driving circuitry on screen and accomplishes the video data processing.
应用推荐