• 挤密桩法地基处理在电力工程中广泛应用,特别是灰土挤密夯扩桩法。

    The foundation treatment of compaction pile method is applied in many power plant projects, especially lime-soil compaction-expansion pile method.

    youdao

  • 利用有限元法研究了连续铸挤工艺中液态金属的动态凝固过程。

    The solidification process of liquid metal in the CASTEX technique was studied by FEM (finite element method).

    youdao

  • 同时结合工程实例,表明将爆破挤淤法用于公路工程的软土处理是可行的。

    The case history presented in the paper proved that it is feasible to apply the method of mud replacement by blasting to the improvement of soft soils in road works.

    youdao

  • 本文采用电阻法对CFRP单向拉挤复合材料的破坏过程进行监测,是对CFRP复合材料的结构健康监控的基础性研究。

    The damage behaviors of CFRP unidirectional pultruded composites were monitored by an electrical resistance method. The project is a basic research on structure health monitoring of CFRP composite.

    youdao

  • 采用有限元法,计算和分析了壁厚不均与椭圆套管在单向均匀和单向椭圆分布外挤力作用下的强度问题。

    With finite element method, the collapse strength of casing with ovality and eccentricity under unidirectional uniform and ellipse distributive force was calculated and analyzed.

    youdao

  • 本文在采用自平衡法静载荷试验的基础上,分别对浙江嘉兴和湖州两个工程中的同一场地挤扩支盘灌注桩与普通直孔灌注桩进行对比试验研究。

    To study vertical bearing behavior of the foundation, a shaft diaphragm wall foundation of bridge in loess area was tested for bearing capacity by use of the self-balanced method.

    youdao

  • 同时结合工程实例,表明将爆破挤淤法用于公路工程的软土处理是可行的。

    The case history presented in the paper proved that it is feasible to apply the method of mud replacement by blasting to the...

    youdao

  • 再次,运用二维轴对称有限元法以及三维有限元法,系统分析了挤扩支盘桩单桩和群桩的承载变形性状。

    Thirdly, the bearing and deformation characteristics of single and group piles are investigated by means of axisymmetric finite element analysis (FEA) and three-dimensional FEA.

    youdao

  • 本文在一个拖动的单缸实验机上,利用油点条痕法显示了活塞上燃烧室凹坑中挤流运动的流谱,研究了燃烧室形状和几何尺寸对挤流谱的影响。

    The squish patterns in engine piston bowls with different geometry are visualized by the method of oil streak in a motored single cylinder test engine.

    youdao

  • 本文对空心件反挤的单位挤压力,采用滑移线法和上限法进行了计算。

    The unit pressure in backward extruding hollow billet has been calculated by the slip line method and the upper bound method.

    youdao

  • 本文利用有限元法对塑料管材的挤出进行模拟。主要讨论了影响塑料管材挤熔接痕形成的因素,以及管子冷却过程的热传递。

    This essay described the FEM simulation of plastic pipe extrusion: the factors of melt line formation and heat transfer of cooling processing were mainly discussed.

    youdao

  • 本文利用有限元法对塑料管材的挤出进行模拟。主要讨论了影响塑料管材挤熔接痕形成的因素,以及管子冷却过程的热传递。

    This essay described the FEM simulation of plastic pipe extrusion: the factors of melt line formation and heat transfer of cooling processing were mainly discussed.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定