结果：应用种植体可提高赝复体的稳定性。
Results: the implants can improve the stability of prostheses.
基于快速成型技术的人耳赝复体的设计与制造。
Design and fabrication of auricular prostheses based on rapid prototype technology.
方法采用医用弹性硅橡胶材料制作牙龈赝复体，并对结果进行观察。
Methods Methods Elastic silicone rubber was used to make spurious complex, then the clinical result was observed.
目的探讨种植体支持的赝复体修复眼眶部缺损的修复技术及临床效果。
Objective to evaluate the clinical result of using osseointegrated implants to retain removable orbital prostheses in repairing orbital defects.
本文首先研究基于CT图像处理与快速成型技术的义耳赝复体修复工艺。
Firstly, the repair technics of auricular prostheses based on CT images processing and Rapid prototyping technology was studied.
目的：将种植体植入相应部位的组织内，以提高对颅颌面赝复体的支持和固位作用。
Objective: To improve the supporting and stabilizing function of craniofacial-maxillofacial prostheses by implants implanted in the corresponding positions.
结果：获得了所设计的附着体支架及赝复体金属基托的实物模型，平均固位力达47N。
Result:The model of the framework and obturator metal based were obtained. The mean retentive force was 47N.
结论：采用附着体和套筒冠修复方式，充分利用残根、残冠固位，可提高赝复体的固位和稳定。
CONCLUSION: Residual roots and crowns can be reserved and improve the retention and stability of maxillary obturator prostheses by fabricated with attachments and telescopic crowns in clinic.
目的介绍用柔性牙龈赝复材料制作牙龈赝复体的制作过程，评价柔性牙龈赝复体的临床应用效果。
Objective the aim of this paper is to introduce the clinical and laboratory procedures of fabricating silicone gingival epithesis and evaluate the long-term effects of the epithesis.
结果：发现杵臼附着式固位的种植赝复体在行使功能时其腭部、牙槽骨、种植体周围骨界面的应力值均远高于杆卡附着式固位的种植赝复体。
Results: the stress values of the ball attachment in the palate area, alveolar bone and implant bone interface were much higher than that of the bar attachment.
本文对四元数体上矩阵奇异值摄动定理给出了推广，且这些结果对复矩阵也是新的。
The quaternion matrix singular value perturbation theorem is generalized and these results are also new one for complex matrix.
提出该岩体晶质铀矿复成因的证据。
对吸收剂进行SEM与XRD分析，并对磁性合金粉体-石蜡样品进行雷达频带复磁导率的测试。
The absorbent was analysed by SEM and XRD and the magnetic alloy powder-paraffin sample was made a complex permeability measurement in the radar frequency.
本文根据粘弹性体的理论与复变函数理论给出了非圆形巷道(洞室等)的粘弹性解析解。
This paper gives an analytic solution of non-circle opening based on linear viscoelastic theories and theory of function of a complex variable.
铜矿填体优十复非性组合优问题。
Copper Mine is a very complex problem of nonlinear combined optimization.
在动载三体磨粒磨损条件下，试验研究了冲击载荷的变化对铸态复相耐磨钢动载磨粒磨损特性的影响。
The influence of varying impact energy on wear resistance of dual phase cast steel has been investigated under impact three body abrasion.
添加复配的抗红外粉体是制造该物质的主要方法。
The main method of manufacturing this material is to add compound anti-infrared powder.
采用合适的TMCP工艺，可以在低碳合金管线钢中获得不同组成比的针状铁素体复相组织。
By using appropriate TMCP process, complex phase of acicular ferrite with different compositions could be obtained in low carbon alloy pipeline steel.
采用高聚合度PVC与增塑剂等共混、复配制备了PV C热塑性弹性体(TPVC)，对TPVC的冲击回弹和压缩性能进行了研究。
PVC thermoplastic elastomer (TPVC) was prepared by plasticization, blending and compounding of high polymerization degree PVC, and its impact resilience and compression properties were investigated.
系统地提出和论述了矿床(体)定位预测的思路与途径，提出喇嘛苏铜矿床为多因复成成因的新观点。
Bring forward and dissertate the approach of deposit or ore body prospecting by the Numbers, and points out a new view that the genesis of Lamasu copper deposit as a polygenetic compound deposit.
目的：探讨兔在体左心室肥厚心肌跨室壁复极不均一性的变化及缬沙坦的影响。
Objective: To investigate the changes of transmural repolarization heterogeneity in intact rabbits with left ventricular hypertrophy (LVH) and the effects of valsartan on it.
通过对复合材料熔体指数、力学性能以及形态结构的比较，探讨了无机组合粒子级复配共混的协同效应。
The compound inorganic particles synergistic hybridization effect was studied by comparing the melt index, mechanics capability and the morphology.
集条染复精梳，纺纱、织造到后期整理于一体。
Collecting dyeing, re-combing, spinning, weaving and finishing.
电镜分析指出，复相组织疲劳性能高的原因是复相组织中的下贝氏体回火后析出短杆状碳化物，能有效地阻止疲劳裂纹的萌生及扩展。
TEM analysis reveals that the precipitation of short-bar-shaped carbides in lower-bainite can prevent effectively from initiation and propagation of fatigue cracks.
液压自动复中缸与辅助接力器共用同一活塞和同一缸体。
The fluid pressure auto resuming middle jar and an assistance Servomotor use the identical piston and the identical cylinder together.
液压自动复中缸与辅助接力器共用同一活塞和同一缸体。
The fluid pressure auto resuming middle jar and an assistance Servomotor use the identical piston and the identical cylinder together.
应用推荐