钢-混凝土组合梁是指钢梁和混凝土板通过剪力连接件连接形成整体共同工作的受弯构件。
Steel-concrete composite beam is a kind of flexural member composed by concrete slab and steel beam via shear connectors.
研究截面宽度对高强混凝土受弯构件性能的影响。
In this paper, the influence of section width on structural behavior of high strength concrete (HSC) bending members is investigated.
该方法也可用于圆钢管混凝土受弯构件的弯矩-曲率关系分析。
The method presented here is suitable for analyzing relationship of moment-curvature about the concrete filled circular steel tubular (circular CFST) flexural members too.
从锈蚀钢筋混凝土受弯构件破坏模式入手,分析其破坏机理与过程。
In this paper, the failure mechanism and process of corroded r. c. Flexural members are analyzed based on the modes of failure.
根据GBJ10——89,提出了双向受弯构件正截面承载能力计算方法。
According to GBJ10-89, computational method of load-bearing capacity for normal section of bi-directional bended components is presented.
对受弯构件受拉翼缘外侧粘贴FRP后的界面剪应力和界面剥离应力进行了分析。
The interfacial shear stress and peel stress between the FRP and the surface of tension flange were analyzed when the FRP was bonded to the tension flange of the bending members.
采用有限元方法,建立适于冷弯截面受弯构件性能分析的非线性有限元分析模型。
It is also presented a finite element analytical model suitable for non-linear analysis of HFB flexural members.
为使构件破坏时充分发挥钢筋的强度,提出了简支受弯构件最小跨度的确定方法。
To exert the strength of the reinforcing bar when the member broken, puts forward a means in measurement of the minimum span length of simple flexural member.
本文研究采用在混凝土构件侧面粘贴碳纤维板这种新形式加固受弯构件的受力性能。
In this paper, the behavior of the flexural RC member bonded with CFRP board on its vertical sides was investigated by the authors recently.
从氯离子侵蚀的钢筋锈蚀模型入手,建立了锈蚀钢筋混凝土受弯构件承载力随机模型。
The stochastic models for the capacity of corroded r. c . flexural members are built based on the models for reinforcement corrosion in marine environment.
本文对钢筋砼受弯构件的延性进行分析和讨论,提出了截面曲率延性系数的计算公式。
By analysing and discussing the ductility of reinforced concrete beams under flexure, the author gives formula for calculating curvature ductility index of section.
在分析大量文献资料的基础上,采用“等效截面”将双向受弯构件转化为单向受弯构件。
Based on the academic analysis, a biaxial bending member is equivalent to a single bending member by the rule of equivalent cross section.
短牛腿与深梁、桩帽基本上属于非受弯构件,其计算理论相对复杂、计算方法也不尽一致。
Corbels, deep beams and pile caps are included basically in non-flexural elements, the calculative theory of which is relatively complicated, and its calculative method of which is not consistent.
圆CFRP-钢管混凝土受弯构件的延性性能要好于圆截面FRP筒内填混凝土受弯构件。
The ductility of the concrete filled circular CFRP-steel tubular members under bending is better than that of the concrete filled circular FRP tubular members under bending.
而冷加工钢筋,尤其是冷轧扭钢筋,用于板类受弯构件中具有较多优越性,宜大力推广应用。
However cold-finished steel, especially cold rolled twisted steel is of more advantages in components in bending such as slabs. Therefore it shall be popularized.
论述钢筋混凝土结构环形截面及圆形截面受弯构件、偏心受压构件强度计算和强度复核的计算方法。
This paper presented a method of strength calculation and strength check of annular and circular section in flexure and eccentrically compressed component for reinforced concrete structure.
本文通过22根钢筋混凝土受弯构件的试验,探讨了混凝土保护层厚度对裂缝间距和裂缝宽度的影响。
In this paper, according to the experimental results of 22 beams, we probe into the influence of concrete cover thickness on crack width and crack spacing.
根据试验结果和新规范受弯构件受剪承载力计算体系,本文提出了迭合受弯构件受剪承载力计算公式。
Based on test results and calculating system of shear strength for members in bending by new code, this paper presents the calculating formulas of shear strength for composite members in bending.
我国钢筋混凝土结构设计规范中,钢筋混凝土受弯构件的刚度公式是在半理论半实验的基础上建立起来的。
In our national Design Code of Reinforced Concrete Structures, the stiffness formulas of Reinforced Concrete Flexural members were based on half theoretical analysis and half test result.
在试验研究的基础上,建立了考虑两阶段受力影响的桥梁加固钢筋混凝土受弯构件斜截面承载力计算公式。
The analysis method and calculation expressions of oblique section consolidation of reinforced concrete bridge are discussed on the basis of test analysis.
针对聚丙烯纤维混凝土的力学性能和钢筋聚丙烯纤维混凝土受弯构件的结构性能,本文进行了如下试验研究。
Mechanical properties of polypropylene fibers reinforced concrete and the properties of reinforced concrete flexural members are studied by means of several experiments.
另外,现行的公路桥涵设计规范,在对桥梁受弯构件承载能力计算中采用了一些基本假定,导致计算结果过于保守。
Besides, the current bridge and culvert design criterion takes some basic postulation during the calculation of the bridge's member in bending, which results in over-conservative numeric value.
使用体外预应力碳纤维板加固受弯构件,可以充分发挥碳纤维板的强度,提高结构的正常使用性能和极限承载能力。
External prestressing CFRP can give full play to the strength of CFRP to improve the structure of the normal use performance and ultimate bearing capacity.
圆截面受弯构件是工程结构中常遇到的一种构件,现行的钢筋混凝土规范给出了圆截面梁全截面均匀配筋的计算方法。
The formula of the carrying capacity of beam of a round section is given in China's design standard of reinforced concrete.
根据GB50010—2002《混凝土结构设计规范》规定的单向受弯构件正截面承载力计算方法确定梁的单向受弯正截面承载力。
According to GB50010-2002 Code for design of concrete structures, the normal section bearing capacity of reinforced concrete beam subjected to single bending is determined.
当配筋特征值不大于0.2时,承载能力极限状态下碳纤维片材的拉应变可以接近或超过允许拉应变,因此可以有效地对受弯构件正截面承载力进行加固;
When the ratio not more than 0.2, CFRP tensile strain can reach or exceed the permissible strain at ultimate capacity state, and therefore CFRP can work efficiently.
当配筋特征值不大于0.2时,承载能力极限状态下碳纤维片材的拉应变可以接近或超过允许拉应变,因此可以有效地对受弯构件正截面承载力进行加固;
When the ratio not more than 0.2, CFRP tensile strain can reach or exceed the permissible strain at ultimate capacity state, and therefore CFRP can work efficiently.
应用推荐