接下来我们看一看内核参数的设置。
每个参数的设置依赖于您当前运行的系统。
The setting of each parameter depends on your current running system.
这些控制由相关技术的参数的设置方式决定。
The controls are governed by how the parameters for the associated technologies are set.
保持其他默认参数的设置不变，并点击Finish。
Leave all Settings of the new project on the default parameters, and click Finish.
并对系统模型参数的设置及系统模型本身提出了修改意见。
Some opinions are presented for setting the parameters of the prediction system and correcting the logic model of this system.
为什么呢？检查JDK_PATH数据库管理器配置参数的设置是否正确。
Why? Check the JDK_PATH database manager configuration file to see if it is set properly.
探讨了阻尼参数的设置、地震波的选取、地震动方向的输入等问题。
Representing amortization reference set-up, earthquake wave access and earthquake motion input as well.
经过研究发现最终结果的准确性很大程度上取决于初始参数的设置。
After the final results of the study found that a large extent depends on the accuracy of the initial parameters set.
Bonita将保存输入参数的设置，返回图10中的连接器创建向导。
Bonita will save the input parameters configurations and will take you back to the earlier Connector creation wizard of Figure 10.
通过一个预先的设置，操作人员可以减少环境参数的设置高达90%以上。
A selection of pre-settings reduce the number of parameters needed to be handled by more than 90 percent.
清洗过程中参数的设置，如清洗温度，清洗时间会对清洗效果产生较大影响。
Cleaning parameters such as cleaning temperature and cleaning time have great effects on the cleaning result.
红外遥控模块通过设计红外发送和接收电路，实现系统软件参数的设置功能；
Infrared remote control device actualizes the system software parameters setting through the design of infrared sending and receiving circuit.
实现了对直流电动机转动参数的设置、启动、停止、加速、减速和显示等功能。
The Paper designs the software which achieves the functions, such as install Parameters, download Parameters, startup, stop accelerate and decelerate.
探讨了用电子模拟仿真软件EWB分析、设计电路的一般方法及一些参数的设置。
The paper attempts to introduce the method of circuit analysis and circuit design with electronic simulation software EWB (Electronics Workbench) and setting up for some parameters.
但是同时可知，良好的估计效果与ukf算法中各个参数的设置情况有重要的关系。
However, it can be known that the parameters of UKF are important to the performance of estimate.
然而，lvmo命令只允许更改专门用于特定VG的lvm pbuf可调参数的设置。
However, the lvmo command only allows the Settings to change for the LVM pbuf tunables that are dedicated to specific VGs.
介绍交流变频调速技术在龙门刨床电气改造中的应用和总体改造方案及有关参数的设置。
The paper introduces the application, main alteration plan and the setting of relational parameters of technique of alternating current frequency conversion in Longmen planer′s electrical alteration.
目的：通过对双源CT各种扫描参数的设置并扫描来分析与探讨这些参数是如何影响图像质量。
Objective To analyze and discuss how the scanning parameters influence the quality of dual source CT(DSCT) images by the various settings and the corresponding scans.
从理论上计算各个参数的设置范围，并且证明小波变换方法比FFT方法有较高的频率分辨率。
Calculates the setting range of each parameter in theory, and proves the method of wavelet transformation has higher frequency resolution than the method of FFT.
这些试探起到过滤器的作用，通过参数的设置和调整，可使它更好地达成对主体信息块的抽取。
These heuristics act as filters that can be parameterized and toggled to perform the web block information extraction.
主要包括硬件接口电路的设计、控制参数的设置以及部分关键的控制代码和实现AD采样的程序流程等。
The design of hardware interface circuits, setting of control parameters, some critical control code, and the flowchart of AD sampling program etc. are described in this paper.
该设备以PLC为控制核心，辅以触摸屏进行堆焊参数的设置和修改，并实时显示堆焊过程中的参数状态；
PLC is the core of this device, supplemented by the touch screen to set and modify the welding parameters and display the state of welding process parameters.
其人机操作界面包括转速波形的显示和存储、电枢电流监控、参数的设置、实验指导书和实验报告调用等功能。
The human-machine interfaces including speed waveform display and store, armature current monitoring, control parameter setting, experiment instruction and report generator are introduced in detail.
为了充分利用以往的经验，用于注塑成型工艺参数的设置，采用基于案例的推理方法用于获取注塑成型工艺参数。
To make the best use of past experience in setting of the injection molding process parameters, case-based reasoning method was used to obtain injection molding process parameters.
求解过程中各参数的设置合理，可以较好地反映尾水管中的主要流动现象，同时也说明了流场计算结果的正确性。
Defined parameters were appropriate, which can reflect main flow in draft tube. It also instructed that the calculation was correct.
经常地，url地址都带有我们称之为参数的动态部分。有多种方式来设置参数。一个基本参数的设置代码如下。
Often, URLs have dynamic parts to them which are called parameters. There are several options for specifying parameters. A basic parameter looks like this.
通过控制程序的MAP图参数的设置，使燃油和燃气供应量逐渐逼近期望值，实现了燃气和燃油供应的动态调整。
With parameter setting of the MAP in the control program, an expected fuel and gas are supplied to the engine system, so dynamic fuel and gas supply is adjusted.
介绍了COMBIVERT型变频器滑差补偿特性的工作原理和功能，总结了滑差补偿特性参数的设置、调试的方法和步骤。
The principle and functions of COMBIVERT frequency inverter slip compensation character, and the setting method and testing procedure of slip compensation character parameters are also summarized.
介绍了COMBIVERT型变频器滑差补偿特性的工作原理和功能，总结了滑差补偿特性参数的设置、调试的方法和步骤。
The principle and functions of COMBIVERT frequency inverter slip compensation character, and the setting method and testing procedure of slip compensation character parameters are also summarized.
应用推荐