我打不开门—卡死了。
我无法操纵这辆汽车，车轮给卡死了。
我无法操纵这辆汽车，车轮给卡死了。
因为它是短暂的，这使得它容易卡死。
Because it's brief, that makes it vulnerable to deadlocking.
阀芯与阀座或衬套卡死，阀杆弯曲等。
Valve core and valve seat or bushing deactivation, valve lever curving and so on.
有杂质吸附在膜片上，动铁芯有卡死现象。
There is some dirt or debris on the membrane, it is blocking the moving iron core.
三通切换阀“卡死”。
应当注意，出口止回阀不能装反或出现卡死现象。
It should be noted that the outlet check valve cannot be installed backwards or stuck.
应当注意，出口止回阀不能装反或出现卡死现象。
It should be noted that exports can not check valve or a card with the anti-death phenomenon.
摧毁一个正在阅读的路牌不会导致你的角色卡死。
Destroying a placed sign while you are reading it will no longer cause your character to become frozen.
修正当上一回合AI玩家失去其回合导致游戏卡死；
The issue of the game getting stuck if the last AI player loses in his own turn.
电磁线圈烧坏C，阀芯卡死，解决办法检修或更换。
B. solenoid valve stuck, burn C, solution repair or replacement.
该方案考虑了两种舵机故障模型：舵机卡死和舵机失效。
Considered actuator fault models include both the actuator-stuck fault and the loss of actuator effectiveness fault.
不过公认的BUG是鼠标出错，还有ESC键按太多会卡死。
But accepted BUG mouse error, and ESC keys by too much will get stuck.
本文研究无人机方向舵卡死时下滑模型建立的方法与处理原则。
This paper researches the method of modeling and principle of establishing model of unmanned aerial vehicle(UAV) during gliding with rudder lock-in-place.
当玩家将尼姆布亚的长矛插在地上的时候，不再会造成卡死的现象。
Players will no longer become stuck on the Nimboya's Laden Pike when driving it into the ground.
在洛阳石化总厂一年多的运行表明，操作方便，未发生阀轴卡死现象；
Application more than one year in Luoyang General Petrochendcal Works showed that it is characterized by convenient operation, good sealing property and no shaft seizing.
伞杆上部的钢丝绳会出到绳槽外并卡死，只有将绳剪断，才能解除卡死。
When the wire rope, upper of the umbrella pole, comes out of the rope groove, it will be jammed. Only cutting off the wire rope can release the jam.
另外还有一些做的粗糙的地方需要改进，比如：4s的照相机应用偶尔会卡死在启动界面。
There are some rough spots here and there; for example, every now and then the 4s's camera app gets stuck on its startup screen.
接下来，向内转动膝盖（向着裂缝的方向），同时扭转岩鞋，直至卡死在岩缝里。
Next, torque your knee inwards (towards the crack), twisting the shoe and locking it into place.
该机采用卧式粉碎机构，轴端设有配重轮，运转过程中不会产生“卡死”现象。
This machinery is a new type horizontal smash mechanism. It is equipped with kit rounds at the fore shaft, so it won't be blocked on the operation process.
水泵不吸水或不排水其原因多为底阀卡死，滤水部分淤塞，吸水高度太高或吸水漏气。
Non-absorbent or water drainage at the end of the causes for the stuck valve, part of the blockage of water, high water or water leakage is too high.
工矿企业电动机在使用过程中，由于机械出现故障造成扫膛、卡死、烧坏线圈等事故。
In the use of electric motor by enterprise, mechanical failure may cause accidents, which result in touch between stator and rotor or stop or damage of coil.
重点研究了盾构刀盘在切削过程中负载冲击和刀盘卡死产生的原因以及冲击带来的影响。
The impact load and its effect as well as the reason of cutterhead deadlocking were mainly studied.
油温升高使阀心受热膨胀，阀套与阀心间的配合间隙减小， 阀心有可能被卡死在阀套里。
The fit clearance between spool and sleeve decreases because of the thermal expansion of the spool caused by temperature increment, so it is possible that spool is deadlocked in sleeve.
油温升高使阀心受热膨胀，阀套与阀心间的配合间隙减小， 阀心有可能被卡死在阀套里。
The fit clearance between spool and sleeve decreases because of the thermal expansion of the spool caused by temperature increment, so it is possible that spool is deadlocked in sleeve.
应用推荐