提出了常剪切应变点的概念。
渗透系数依赖于塑性剪切应变(率)。
The permeability coefficient is dependent on the plastic shearing strain (ratio).
对考虑刚度劣化时的常剪切应变点进行了讨论。
The constant shear strain point accounting for the degradation of stiffness was discussed.
根据非局部连续介质模型,提出了一维二阶剪切应变率梯度格式。
One dimensional shear strain rate gradient formation of the second order is proposed based on the non-local continuum model.
扩容角越大,剪切带最终可以获得越来越高的剪切应变和体积应变。
Higher DA results in higher values of shear strain and volumetric strain in shear band.
在应变硬化阶段,可以从未来震源观测到前兆剪切应变率异常条带。
In the strain-hardening stage, an effective precursor can be observed from the future earthquake source.
从位错理论出发导出了湿软土壤的剪切应力—剪切应变—时间关系。
The shear stress - shear rate - time relationship of wet and soft soils is determined from the point of view of dislocation theory.
同时由应力路径旋转对模量的影响也随着剪切应变的增加而逐渐衰减。
At the same time, the effect of stress path circumgyration on shear modulus decreases gradually along with the increase of shear strain.
通过设计ecap模具的几何结构,研究了剪切应变累积效应的度量方法。
With structural design of ECAP die, the accumulated effect of shear strains under ECAP was calculated.
利用力学和有限元原理,推导出横隔板、横隔墙的抗剪刚度、剪切应变能。
Both shearing strain energy and shearing stiffness of diaphragms and side walls were deduced on the basis of the principles of mechanics and finite element.
本文介绍了一种新型实用剪切应变称重传感器的原理、技术指标和生产工艺。
This paper introduces the working principle, technical characteristics and fabricating process of a new practical shearing strain weighing sensor.
强震通常发生在剪切应变率的高值区及其边缘,尤其是与构造变形背景相一致的剪应变率高值区。
Strong earthquakes occurred in the high-value region and its margins of shear strain rate, especially in the high-value region of shear strain rate in accordance with tectonic deformation background.
当扩容角较高时,应力峰值时试样内部的最大剪切应变增量较高,因而试样破坏的前兆比较明显。
Higher DA leads to higher value of maximum shear strain increment within the specimen. Therefore, more apparent precursor to failure can be observed at higher DA.
为了避免膜闭锁和剪切闭锁,在计算单元应变能时,用假定应变代替膜应变和平面外的剪切应变。
To alleviate the membrane and shear locking phenomena, the membrane strains and the out-of-plane shear strains are replaced with assumed strains in calculating the element strain energy.
提出了由潮汐线应变的组合观测资料获取地表平面应变状态和对潮汐剪切应变进行数值模拟的方法。
A method is presented, by which the plane strain state on the earth's surface can be obtained with the combination of tidal line strain data and the tidal shear strain can be simulated numerically.
角刚度(又称弹性比力矩)及弹性件在最大摆角下的剪切应变是固体发动机柔性接头设计的重要指标。
Angular stiffness and elastomer shear strain on maximum swinging Angle are important indexes in flexible joint design of solid rocket motor.
剪切应变率(或应变)局部化区域与体积应变率(或应变)的位置重合,局部化区域就是岩样最终的破坏位置。
The location of shear strain rate localization coincides in position with the location of volumetric strain rate, which is the actual failure zone of rock.
建立了局部(塑性)剪切变形梯度与局部(塑性)剪切应变分布之间的关系及速度梯度与应变率分布之间的关系。
The relation between the gradient of local (plastic) shear deformation and the local (plastic) shear strain and that between the gradient of velocity and the strain rate were established.
首先,由于在应变软化阶段的峰值强度的剪切应变局部化启动的纵向和横向的塑性变形引起的耗散能进行了分析。
Firstly, dissipated energies induced by axial and lateral plastic deformations due to shear strain localization initiated at peak strength in strain softening stage is analyzed.
由于微结构效应,基于梯度塑性理论的剪切带内部的最大塑性剪切应变及最高温度的预测值高于经典理论的预测值。
The prediction values of shear strain and temperature in shear band based on gradient-dependent plasticity are higher than those by use of classical elastoplastic theory.
本文基于高阶剪切变形理论,考虑横向正应变和横向剪切应变的影响,对受热复合材料层合板壳的非线性热动态响应进行分析。
Based on a model of a cantilever beam system with clearance restriction, its nonlinear dynamic response to harmonic excitation are studied qualitatively in experiments.
利用自行改装后的三轴蠕变仪对海相沉积的营口软土进行蠕变试验,获得了在不同围压、不同偏应力条件下的剪切应变与时间关系数据。
The relationship between shear strain and time of Yingkou soft soil is obtained under a series of different cell pressures and different deviator stresses.
本文采用四边形面积坐标,利用假设剪切应变场方法和广义协调理论构造出一个具有12个自由度的四边形厚薄板通用弯曲单元TACQ。
In this paper, a new quadrilateral thin-thick plate bending element with only 12 degrees of freedom, TACQ, is developed by using the area coordinate method.
当进一步对碎片施加应变,碎片的长度不再减少时,我们测量这个长度,并由此计算界面剪切应力。
The fragment length at which no more breaks occur when applying further strain to the specimen is measured and from this calculation of the interfacial shear stress is done.
根据旋转应变及其他标志,确定本矿区两条韧性平移剪切带的剪切动向为右行剪切。
From the rotation strain and other evidences, the shear direction of the two ductile transcurrent shear zones are determined to be dextral.
土体总的变形由三部分组成:即弹性应变、与体积屈服机制相关的塑性应变和与剪切屈服机制相关的塑性应变。
The total deformation of soils consists of three parts: elastic strain, plastic strain related to volumetric yielding mechanism and plastic strain related to shear yielding mechanism.
针对板材剪切与冲裁加工的特点,设计了一种应变片式位移传感器。
A displacement sensor of strain foil is designed aiming at the sheet shearing and blanking processes.
按照剪切滞后理论和应变硬化规律,研究微复合材料的变形和应力状态。
The deformation and stress condition of the micro-composite are studied according to the shear-lag theory and strain-hardening law.
按照剪切滞后理论和应变硬化规律,研究微复合材料的变形和应力状态。
The deformation and stress condition of the micro-composite are studied according to the shear-lag theory and strain-hardening law.
应用推荐