This layer has material const ants which govern the stiffness across it and has zero thickness.
该层的材料常数用劲度常数来描述，其层厚为零。
Considering that the crack thickness is usually very small, it can be taken as a'surface defect' with zero thickness.
根据裂纹的特点，可以把它近似为一个没有厚度的面缺陷，其作用由分布在裂纹面上的等效电流偶极子层代替。
Based on the study of features of sheet metal parts and Zero Thickness Hypothesis, a new mechanism of naming and identifying topological entities of a feature model is proposed in this paper.
本文在对钣金件特征研究和“零厚度”假设的基础上，提出了一种钣金件拓扑元素命名和辨别的新方法。
Sewn-through shells (zero wall thickness) are a poor idea.
车缝-通过弹(零壁厚)是一个贫穷的想法。
With the increase of the ground thickness the fluctuation is reduced progressively to zero.
随着土层厚度增加，这种振荡现象逐渐减弱直至消失。
Our proprietary setup procedures enable us to plate in deep cavities, while maintaining electroform thickness with zero porosity.
我们拥有专利权的设置程序可以进行深腔镀膜，同时在无孔隙的情况下保持电镀厚度。
The critical thickness is determined from the zero formation energy of a misfit dislocation. i. e. the amount of reduced mismatch strain energy equaling the amount of creased dislocation self energy.
利用位错形成能等于零(即错配应变能的降低等于位错自能)的条件，得到了外延生长薄膜的临界厚度。
For the case of hydrodynamic noise, in which the range of the frequency-thickness product of interest is relatively low, the symmetric zero-order mode dominates the noise radiation.
对于水动力噪声情况，感兴趣的频率厚度乘积相当低，这时零阶对称模式对噪声辐射起主要作用。
The quantitative analysis shows that the numerical simulation cases are different from the experiment results in the place of the transition point, film thickness at low speed area and the zero point.
定量比较表明：计算结果与实验结果在过渡点位置、低速区膜厚值大小、零点位置等方面存在差异。
The three new are as follows, international bulging and soft reduction, new spray technology in secondary cooling and on line quick width adjustable and thickness adjustable device for zero segment.
介绍了最近开发成功并应用的三项厚板坯连铸新技术 ：人为鼓肚轻压下 ，二次喷淋新技术及在线快速调厚调宽的零号扇形段。
Nonlinear rheological models of thick and zero-thickness structural planes are presented. And incremental expressions of finite element for simulating creep of the structural planes are derived.
提出了有厚度和无厚度地质缺陷的非线性蠕变模型，推导了模拟上述地质缺陷蠕变的有限元增量表达式。
When advancing large thickness cutting, frequency tracking shall be properly adjusted slow, you'd better adjust it to stable cutting from zero position and ammeter pointer no longer shakes sharply.
在作大厚度切割时，变频跟踪应适当调慢，最好从零位起调至切割稳定，电流表指针不再激烈晃动。
When advancing large thickness cutting, frequency tracking shall be properly adjusted slow, you'd better adjust it to stable cutting from zero position and ammeter pointer no longer shakes sharply.
在作大厚度切割时，变频跟踪应适当调慢，最好从零位起调至切割稳定，电流表指针不再激烈晃动。
应用推荐