In order to prevent the yield-point elongation occurring the manganese equivalence in alloy must exceeds 1.61%, and the threshold value of Martensite volume fraction is 7%.
为了不发生屈服点延伸，合金中的锰当量必须超过1.61%，马氏体体积分数的门槛值为7%。
According to yield-strength, the two different arriving approaches were distinguished, and two different kinds of yield-point and yield-curve were determined.
就屈服值区分了两种取值方法，并确定出两类屈服点和两类屈服曲线。
Economists on Wall Street have indicated that a 25 to 60 basis-point increase in yield may occur on the 10-year Treasury bond - pushing rates up to around 3%.
华尔街的经济师们一直预测10年期国债收益率可能上升25 -60个基点——这样收益率将升至3%。
At this point, you reach a point of diminishing marginal returns where increasing the heap size further does not yield a proportional performance benefit.
至此，您的边际收益将开始逐渐递减，因为进一步增加堆大小将不会带来成比例的性能改进。
The reverse is the case.French ten-year bonds trade on a yield more than a percentage point higher than their German equivalents, even though both share a AAA rating.
相反的例子，法国十年期国债的收益率比德国的十年期国债收益率高出超过百分之一，尽管他们两国都是AAA评级。
When the stress reaches the yield point, a large increase in strain occurs with no increase in stress.
当应力达到屈服点，应变会急剧增大而应力保持不变。
If the design is based on the strain hardened properties, the allowable design stress will usually be above the actual yield point of the HAZ.
如该设计基于应变硬化性能，设计应力通常在HAZ实际屈服点以上。
Because of the lower yield point of rotor material, the local plastic deformations are found during operation at rate speed.
由于转子材料屈服点较低，在额定转速时，局部会出现塑性形变。
The conventional photoelastic modes and procedures suffice to indicate whether or not the yield point of the material of the prototype will be exceeded.
常用的光弹性模型和方法能够指明原型材料的屈服点是否将被超过。
An experimental and theoretical study of the earthquake mitigation effect of hysteretic dampers using ultra low yield point steel was presented in this paper.
本文通过试验研究和理论分析探讨极低屈服点软钢阻尼器的减震效果。
It must be emphasized that the absence of a definite yield point does not in itself imply that the material has a low ductility.
必须强调的是，没有明显的屈服点并不意味材料有较低的韧性。
High strength plate also known as high strength plate, low alloy high strength plate, high strength welding plate. It is characterized by high strength and high yield point.
高强板又称高强度板，低合金高强板，高强度焊接板。主要特点是强度大，屈服点高。
The value of stress under air pressure test shall not exceed 80% of the yield point of the material in test temperature;
气体压力试验时的应力值，不得超过试验温度下材料屈服点的80%。
The value of stress under hydraulic pressure test shall not exceed 90% of the yield point of the material in test temperature;
液体压力试验时的应力值，不得超过试验温度下材料屈服点的90%；
The precision of Cam clay model is poor and the Sekiguchi Otha model gives excess deformation and a singularity point on the yield locus.
采用关口—太田各向异性模型，实测资料表明预测的变形偏大，且屈服面上有奇异点。
The sample yield and the fugitive constituent decreased with time, but the softening point and the content of toluene insoluble components increased.
随着反应时间的延长，样品收率、挥发份产率不断降低，而软化点和甲苯不溶物含量则不断升高。
The yield point represents the dividing line or transition from the elastic to the plastic region of the curve.
屈服点是弹性变形区域到塑性变形区域之间曲线的过渡点。
Beyond the yield point, the material will continue to deform, but with less stress than before, because the material has begun to yield.
超过屈服点之后，材料会继续变形，但是因为材料开始屈服，应力会减小。
It was observed that the lower yield point was subject to a greater degree of scatter than that of the upper yield point.
业已观察到下屈服点比上屈服点易产生更大的散布度。
The stress strain curves displayed the characteristics of low yield point, continuous yield and no obvious yield point.
结果表明 ：其应力—应变曲线表现出屈服点低、连续屈服、没有明显的屈服点等特性 ；
Viscoelasticity is related to some properties such as gel point, gel strength, yield stress and thixotropy.
粘弹性与胶凝温度、胶凝强度、屈服应力和触变性等参数有关。
The effects of experimental factors on both product yield and purity were analyzed and investigated from the point of view of nitration.
分析了几种试验因素对产品收率和纯度的影响，并从硝化作用的角度对这些影响进行了探讨。
After using dewaxing aid, the filtration rate and the dewaxed oil yield were improved, the oil content in slack wax was decreased, and the dewaxed oil changed little in solidification point.
使用脱蜡助剂后，过滤速度、去蜡油收率提高，蜡膏含油量降低，去蜡油凝点变化不大。
The yield of catalytic cracking gasoline increased by1. 29 percentage points and the diesel yield decreased by 1 percentage point.
催化裂化汽油收率提高了1.29个百分点，柴油收率下降了约1个百分点。
The yield point is the stress at which there is an appreciable increase in strain with no increase in stress, with the limitation that, if straining is continued, the stress will again increase.
屈服点是在应变有可观增加，应力没有增加的应力极限，在这个极限下，如果应变继续增加，应力就也会增加。
Don't yield a point in the argument.
不要对争论中这一观点让步。
Attaching amino acid to the resin is the sticking point in the whole synthesis, because it has the most important effects on the yield and purification of ultimate product.
第一个氨基酸与树脂连接反应是整个合成过程中最关键的反应，它的好坏直接关系到最终产品的产率和纯度。
Shear yield stress was defined as the intercept point on the Y-axis.
剪切屈服应力被定义为Y轴上的交会点。
Weld shrinkage-induced local strain to yield point strain often several times, than the strain due to the load is much larger;
焊缝收缩诱发的局部应变时常达到屈服点应变的数倍，比荷载引起的应变大得多；
The commercial Banks face four kinds of main interest: Fix the price risk, basic point risk, option risk, yield curve risk.
商业银行所面临着四种主要的利率风险：重新定价风险、基本点风险、选择权风险、收益曲线风险。
应用推荐