This paper introduces the structure characters and working principle of mould for cold stamping buttefly pallet.
介绍用于碟形托盘冷冲压成形模具的结构特点及工作原理。
The design of its molding part was used in the mold, inject system and other make up, and working process of the mould are specified in detail.
详细地叙述了模具成形零件的设计、液压侧抽芯机构、浇注系统和其他结构的设计过程，以及模具工作过程。
Through the technology analysis of the complicated constitution of plug jacket, the injection mould structure and the working process were determined. The design characteristic was introduced as well.
通过对插接护套复杂结构的工艺分析，确定了该类制件的注射模结构、工作过程，并对其设计特点进行了介绍。
Though the technological analysis of the structure of the accumulator tank , the structure and working process of the injection mould for the type of parts are determined.
通过对蓄电池槽结构的工艺分析，确定了该类制件的注射模结构、工作过程，并对其设计特点进行了介绍。
Over detail analysis of mould structure working process and disassemble dies process an injection mould design method of solving this kind of plastic parts is introduced.
通过对模具结构、模具工作过程、卸模过程的详细分析，介绍了一种解决此类塑料件注射模的设计方法。
Present article discussed the design and working mechanism of the insertion in the horizontal injection mould.
本文论述卧式塑料注射模中非刚性嵌件安放机构的设计及工作实现原理。
The design and machining technology of its molding part, the design of the injecting system and other structures, as well as the working process of the mould are specified in detail.
详细地叙述了模具成型零件的设计与加工工艺过程，浇注系统和其它结构的设计过程，以及模具工作过程。
The general design principle of gas-assisted injection mould design is discussed. The working principle and selection method of gas pins are introduced.
阐述了气体辅助注射模具设计的一般原则，介绍了气针的工作原理和选择方法。
The structure and process requirement of the parts of the insulator was analysized, and the structure and working process of the injection mould for insulator was presented.
分析了绝缘器零件的结构及工艺要求，介绍了绝缘器注射模的结构特点及工作过程。
For most of seals, we can directly adopt "not directly parting on working lip" to meet products' request, for a few of seals that we can't do so directly, we can add mould core to transform it.
绝大部分的密封件产品，我们可以直接采取“在工作唇边不直接分型的方法以满足产品要求”，小部分不能直接采取的，加模芯来转换，使其工作唇边不直接分型。
Oscillating curve of different locations directly relates to whether the cast steel working is normal during the operation of the mould.
结晶器在工作过程中，其上不同部位的振动位移曲线是否一致直接关系到铸钢过程的正常工作。
The working course, characteristic and the structure of the compound mould are introduced.
介绍了复合模的结构、特点及工作过程。
The effect of blank quality in cold extrusion on the damage way and service life of working parts (mould and die)is analysed, and some countermeasures presented.
分析了冷挤压毛坯质量对模具的工作部分（上、下凸模和凹模）的损坏形式和寿命的影响，指出了保证毛坯质量应采取的措施。
Through the analysis of the structure and technological property of the of the doorknob, the mould structure, the working process of the mould, the design of the key part of the mould are introduced.
通过对门体堵盖的结构和工艺性分析，介绍了该模具的结构设计、工作过程及关键零部件的设计。
The structure and the working process of the foaming mould for the adapter were introduced.
介绍了适配体发泡模具的结构及工作过程。
It introduces the mould structure and working principle of the injection mould with inside pattern drawing from three directions for core. Point out the design gists of the mould.
介绍三面内抽芯盒盖注射模的模具结构及工作原理，并指出了该模具的设计要点。
The structural characteristics and its working process of the compound mould are introduced in this pa-per.
介绍了复合模的结构特点及工作过程。
The working principle and the working process of adsorption plastic mould of tank are introduced.
介绍箱体吸塑模的工作原理和工作过程。
The structure characteristics of the protection guide bush of shoot nail were analyzed. The structure, machining process of the cavity and the working process of injection mould were introduced.
分析了射钉保护导向套的结构特点，介绍了注射模的结构、型腔的加工工艺和工作过程。
Review the content of each working procedure in the process of mould design.
评审模具设计过程中各工序内容；
Finishing machining as the last procedure of mould machining usually is the most important working procedure, its finishing quality affects directly the final quality and using performance of product.
光整加工作为模具加工的最后一道工序，其加工质量一般影响着产品的最终质量和使用性能。
The structure of the injection mould, the design plan of the gate and the working course of the mould are introduced.
介绍了注射模结构，浇口设计方案和模具工作过程。
The duty working is to accept customer need designing the required mould, clamp, and supporting part mainly.
工作职责主要是接受客户需求设计所需模具，夹具，和配套零件。
Based on the analysis of the structure and technological property of the surface lid, the main points of the design and the working process of the injection mould for the surface lid were introduced.
通过对影视盒面盖的结构及工艺分析，介绍了面盖注射成型模具的设计要点及模具的工作过程。
The technological characteristics of spare parts of the plastics of tap ware analyzed. The structure and working process of the injection mould for forming tap ware introduced .
分析了水龙头的塑件工艺特点，介绍了水龙头注射成形模结构及模具的工作过程。
A dissertation is made on every parts of the structure and working principle of the compression mould.
分析了该塑件的特点，给出了实用的压模结构，论述了模具结构设计和工作过程。
The second working cycle begins after the mould is closed.
第二个工作循环开始后，模具闭合。
The second working cycle begins after the mould is closed.
第二个工作循环开始后，模具闭合。
应用推荐