The grinding system which uses linear motor as a wheel feed drive is introduced.
介绍了利用直线电机作为砂轮进给驱动的磨削系统。
The regulating wheel feed slide is supported on dovetail needle roller guideway and a differential leadscrew is used for performing feed motion.
导轮架进给导轨采用燕尾形滚针导轨，进给用差动丝杆；
When we are there, we will go to play Ferris wheel first and then we are going to feed the birds in the park.
当我们在那里的时候，我们打算先去坐摩天轮然后我们就去喂公园里面的鸟。
The transverse method, in which both the grinding wheel and the workpiece rotate and longitudinal linear feed is applied to enable grinding of the whole length.
横向方法：这种方法中砂轮与工件均旋转且采用线性纵向进给以保证能磨削整个长度。
Two, feeding mechanism: feeding mechanism is to rely on a pair of or two of the feed wheel to press the wire, in order to feed wheel rotation to drive the wire straight ahead of the device.
送料机构：送料机构是靠一对或两对送料轮压紧钢丝，以送料轮的旋转带动钢丝直线前进的装置。
Grinding wheel for the rotating main movement, workbench as a vertical reciprocating motion, grinding wheel rack for intermittent movement into the vertical and horizontal feed movement.
砂轮作旋转主运动，工作台作纵向往复运动，砂轮架作间歇的竖直切入运动和横向进给运动。
By changing the speed of grinding wheel, its swing frequency and the feed speed of shaft direction, different experiment results were got.
通过改变砂轮转速、砂轮摆动频率、轴向进给量，获得了一些具有对比性的试验结果。
The hardness of the rubber contact wheel, the grinding depth of the workpiece per feed once.
探讨橡胶接触轮硬度、每次进给的磨削深度、磨削力和砂带磨损对工件表面粗糙度的影响。
Feed system adopts feeder suction feeder. Cellular suction wheel. Automatic positioning.
送纸系统采用飞达吸风送纸装置。蜂窝式吸风轮。可自动定位。
Some main processing parameters are briefly introduced, such as speed of main shaft, feed rate, shape of spinning wheel, deformation rate of each step and structure of template.
对主要工艺参数如主轴转速、进给率、旋轮形状、道次变形率、模板形式等作了简要介绍。
The water feed channel (or Flume) continues to follow the curve of the wheel downwards to a point directly underneath the axle where it flows into the tailwater stream.
水饲料通道(或水槽)继续遵循车轮曲线向下一个直接指向桥底下的地方流进尾水流量。
The influence of depth of grinding, feed rate and circular linear speed of the grinding wheel on the grinding forces with respect to the maximum chip thickness of a single active diamond was analyzed.
从单颗金刚石最大切削厚度的角度，分析了磨削深度、进给速度和砂轮线速度对磨削力的影响。
It is showed that the surface roughness is mainly related with the average grain size and feed per wheel revolution for the brittle materials such as single crystal silicon.
研究结果表明，对于微晶玻璃等脆性材料，其表面粗糙度主要与砂轮的平均磨粒尺寸、砂轮速度、进给量及磨削深度等因素有关。
It is shown that the surface roughness is mainly related with the average grain size and feed per wheel revolution for the brittle materials such as single silicon.
研究结果表明，对于单晶硅等脆性材料，其表面粗糙度主要与砂轮的平均磨粒尺寸、进给量等因素有关。
The increase of the wheel speed, the swing frequency and the feed of shaft direction conduce to improving the grinding efficiency.
增加砂轮转速、砂轮摆动和轴向进给量可以提高单晶金刚石的研磨效率。
The ratchet wheel and pawl of automatic knife feed mechanism in PASSIM80 cigarette maker had to be replaced frequently because of serious wear.
针对PASSIM 80卷烟机刀头自动进刀机构存在进刀棘轮、棘爪磨损较快，更换频繁等问题，对该机构进行了改进。
The star wheel is an important part of Longjiang-120 head-feed combine.
拨禾星轮是龙江-120型联合收割机上的一个重要零件。
The technological parameters such as electrolysis current, the rotation speed of grinding wheel and the feed rate etc, have been optimized.
研究了砂轮转速、进给量等工艺参数对石英玻璃表面粗糙度的影响；
The properties of CBN wheel in creep feed grinding the high temperature alloy and the characteristics of electroplated CBN wheel are introduced.
介绍了CBN 砂轮缓进给磨削高温合金的磨削性能及电镀CBN砂轮的磨削特点；
Both the grinding wheel and the workpiece rotate during the operation and feed is applied in the longitudinal direction.
作业时砂轮和工件都回转并且采用纵向进给。
Through theoretical derivation and experimental verification, a new method is obtained for further reducing tooth curve error of oblique gear and for choosing feed gear wheel.
在应用无差动法滚切斜齿圆柱齿轮的基础上，通过理论推导和实验验证，得出进一步减少斜齿轮齿向误差的可行的挂轮选配新方法。
The feed speed and quantity of the grinding wheel, grinding pressure, rotating speed of the feeding plate all can be programmed on the computer screen.
具有自动检测、补偿、报警功能，其砂轮进给速度、进给量、磨削压力和送料盘的转速都可以通过显示屏进行编程。
Check for wheel position in the tape feed direction.
检查料带给料方向时的棘转位置。
Use flexible resin wheel to feed paperboard.
采用柔性太阳轮输送纸板。
Use flexible resin wheel to feed paperboard.
采用柔性太阳轮输送纸板。
应用推荐