The welding spot is small, firm, could avoid dry joint.
激光焊接焊点小，焊接牢固，有效避免虚焊不良的出现。
Brightness and excellent electric conductivity welding spot after welding.
焊后焊点光亮，导电性能优良。
The computer control the welding spot position and power, Quick change, Run stability.
电脑控制焊点位置与能量，设备调试时间短，易切换，生产效率高。
To avoid welding spot cracking and decreasing physical strength during cutting process.
切割过程中，有效减少应力发生，防止焊点崩裂；
The solder alloy after the improvement improves wetting property and welding spot strength.
改进后的焊料合金提高了其润湿性能和焊点强度。
Give the detail requirements for welding spot, welding equipment and product inspection during welding.
给出了产品施焊中对施工现场、设备及产品检验的具体要求。
Feature: Wide suitability, firm welding spot, easy operation, stable function, safety& stability and so on.
特点：该机具有适应范围广、焊点牢固、操作方便、性能稳定、 安全可靠等优点。
It has small welding spot, appealing in appearance, reliable in quality, and reducing the cost to the lowest level.
使用本发明方法修复的眼镜架焊点小，外观美观，质量可靠，使眼镜架经修理的影响下降到最低。
Layer can be used to connect steel stamping forming diamond-shaped network, with gas shielded welding spot on the plate.
连接层可用冲压成型的钢质菱形网，用气体保护焊接方法点焊于钢板上。
With brand new design, noiselessness and excellent quality in the welding spot, the welder is able to precisely control the welding energy.
设计新颖，能精确控制焊接能量，无噪音，焊点质量好。
During the course of forming the welding spot, checking and controlling spot welding current value is the key to assure the welding quality.
在焊点形成的过程中，点焊电流有效值的检测与控制是保证焊接质量的关键。
With the welding spot fatigue lifetime pre-estimation method, by combination of the finite element analysis and stress calculation, the welding spot fatigue damage under actual load can be calculated.
采用焊点疲劳寿命预估方法，通过有限元分析并结合应力计算，即可计算出实际载荷工况下的焊点疲劳损伤。
As an example, a robot doing spot welding one month can be reprogrammed and switched to spray painting the next.
比如说，一个机器人做了一个月的点焊，可以重新编程，下个月转向喷漆。
Traditional robots, the kind you might find spot-welding a car frame, can be programmed to carry out a very precise sequence of tasks but only within rigidly structured environments.
传统的机器人，比如你在工厂见到的点焊车架的那种，它们能按照程序执行一系列十分精确的操作，但是必须在严格控制的环境下。
When spot-welding, for instance, a robot has to touch the metal with an electrode.
例如，当点焊的时候机器人必须用电极接触金属。
Using a laser, the robot can make highly accurate welds and position itself for each one a lot faster than it could if it were spot-welding in the normal way.
与传统方法相比，利用激光，机器人可以高精度高效率的完成焊接。
The quality of resistance spot welding of low carbon steel and high strength low alloy steel is studied by looking into the dynamic voltage characteristics of the electrodes.
本文通过对电阻点焊电极电压动态特性的分析，研究了低碳钢及低合金高强度钢电阻点焊的质量问题。
This paper discussed the application of artificial neural network at the resistance spot welding of aluminum alloy.
针对铝合金的电阻点焊，研究了人工神经网络在点焊质量估测中的应用。
The experiment shows that by using inverter spot welding, the average intensity of the welded spot is increased while the splash rate and the incomplete penetration rate are descend.
实验结果显示，采用逆变焊机进行焊接，焊点的平均强度有所提高，飞溅率和未焊合率均有大幅度降低。
The qualitative judgment system based on fuzzy control was built after analyzing the relation between quality of spot welding and the box fractal dimension of signals in spot welding.
在对焊点质量与焊接过程中信息的盒维数统计物理关系的分析基础上建立了基于模糊控制理论的焊点质量判定系统。
The technology used in the WISA family of products has many USES, from controlling pumps and valves to directing spot-welding robots.
应用于WISA产品家族的技术具有许多用途，从控制泵和阀门到指挥点焊机器人。
On the basis of digital signal process and nondestructive testing, the effect of welding process on the frequency spectrum of the current signal in AC spot welding is analyzed.
在数字信号处理及无损检测的理论基础上，分析了焊接过程对电流信号频谱的影响。
A controller applied to IGBT inverter spot welding machine is introduced in this paper.
本文介绍一种应用于IGBT逆变式点焊机的点焊控制器。
The fine effect was gained to improve welding quality of a certain spaceflight igniter by the intelligent spot welding machine with waveform control.
研制的波形控制智能型电阻电焊机在提高某航天火工品的焊接质量方面取得了良好的效果。
By analyzing the effect of each factor on the welding quality, the optimal spot welding parameters of automobile steel plate can be selected easily.
通过分析各因素对电阻点焊质量的影响，可以方便地得到汽车用钢板电阻点焊的最佳工艺参数。
Not only it is fixed with any suspending and stationary spot welding machine, but also it is fixed with any projection welding machine, protable spot welding gun and welding robot.
它不仅可以与悬挂式点焊机、固定式点焊机配套使用，而且还可以与固定式凸焊机、一体化焊机和焊接机器人配套使用。
Then a lot of experimental data about welding parameters and corresponding spot welding quality were supplied to the ANN for training.
然后将试验得到的大量点焊工艺参数与相应点焊接头质量的试验数据提供给神经网络学习。
The mechanism that would bring splash welding by the intelligent resistance spot welding machine with waveform control and the spot welding machine with cap energy storage processing were discussed.
讨论了采用研制的“波形控制智能型电阻点焊机”及其研制的“电容储能点焊机”进行焊接时飞溅的产生机理。
This paper proposes a procedure for artificial neural network (ANN) in spot welding, and establishes spot welding parameter selecting ANN systems and spot welding joint quality predicting ANN systems.
将人工神经网络技术(ANN)引入点焊领域，建立了点焊工艺参数选择ann系统和点焊接头质量预测ann系统。
This paper proposes a procedure for artificial neural network (ANN) in spot welding, and establishes spot welding parameter selecting ANN systems and spot welding joint quality predicting ANN systems.
将人工神经网络技术(ANN)引入点焊领域，建立了点焊工艺参数选择ann系统和点焊接头质量预测ann系统。
应用推荐