F1 and F2 heavy gear of BENGANG 1700 Mill are the biggest welding gears produced by our company so far.
本钢1 70 0轧机改造项目中的F1、F2大齿轮是迄今为止我厂生产的最大的焊接齿轮。
The application results show that laser welding can meet higher strength stress demands for those fatigue load parts, such as intake and exhaust valves, timing gear, suspension equipment.
应用结果表明：对于进排气门、正时齿轮和悬架装置等承担疲劳载荷的零部件，激光焊接可满足其较高的强度要求；
This article introduces the process and characteristics of clutch gear welded by vacuum electron beam and jig design for better welding quality.
论述了离合器齿轮采用真空电子束焊接的工艺过程及特点，并设计夹具以保证焊接质量。
Through the analysis of material and construction, the dissimilar steel gear is successfully welded using stress reduction zone by heating and proper assemble and welding sequence.
通过对铸焊齿轮的材料和结构的分析，利用“加热减应区”法及适当的装配焊接顺序，成功地焊接了异种金属的合金钢齿轮。
Procedure for welding broken teeth of large gear is presented in this article, The procedure developed is easy, simple, low cost and with better result.
介绍了大齿轮断齿的补焊修复新工艺，该工艺简便易行，耗费低廉，效果良好。
The gear disk of high speed and movable teeth are welded through special welding, it makes the teeth is durable, safety and reliable.
高速齿盘与活动牙齿经特种焊接，使活动牙齿坚固耐用安全可靠。
In traditional technology, cup-shaped thin-walled inner gear is produced by stamping two pieces of the part separately, and then welding together.
在传统工艺中，杯形薄壁内齿轮采用切削制齿与焊接工艺相结合的方式进行生产。
The results show that there are no cracks and dimension deformation within welding zones, and the hardness of welding zones meets the requirements of the ring gear.
结论表示，焊缝区没有裂纹，产品尺寸及焊缝区硬度均满足产品要求。
Detailed analysis is made of the reasons why fissures, peeling-off, and tooth breaking exist in the build-up welding layer of cast WC for hardening material of steel-toothed gear drills.
在钢齿牙轮钻头强化材料中，详细地分析了铸造碳化钨堆焊层产生龟裂、脱落和断齿的原因。
For surfacing welding or repair the wear out face made by low carbon steels and middle carbon steels, as axle, gear and blade of mixer.
堆焊或修复低碳钢、中碳钢及低合金钢磨损表面如车轴、齿轮和搅拌机叶片等。
This series use screws to compress the work pieces. The welding process is finished under the reasonable current gear and upset force in the man-controlled time.
该系列对焊机采用螺杆压紧工件，选择合适的电流档位和顶锻力，人控焊接时间完成焊接过程。
This series use screws to compress the work pieces. The welding process is finished under the reasonable current gear and upset force in the man-controlled time.
该系列对焊机采用螺杆压紧工件，选择合适的电流档位和顶锻力，人控焊接时间完成焊接过程。
应用推荐