The stirrer with bigger shoulder contributes to the transformation of plasticity in the direction of weld thickness, it is easier for onion rings to expand in the weld thickness direction.
轴肩较大的搅拌头有利于塑性金属在焊缝厚度方向上的迁移，洋葱环更易于在厚度方向上扩张。
Applicable to all kinds of ingredients containing PVC leather material, the thickness of leather, belts, conveyor belt, treadmill belt fitting and the connection and weld.
适用于各种含PVC成份的皮料、厚度的皮革，皮带，输送带，跑步带的贴合和接驳和熔接。
Unless otherwise specified, all Pacific valves will be supplied with butt weld ends conforming to ANSI B16.25 either Fig. 2(b) or 3(b) depending on the nominal pipe wall thickness of the valve wall.
除非另外指定，所有美国太平洋阀门都配置符合ANSI B16.25标准的对焊连接端口，并根据阀门壁厚和管道壁厚确定是属于型号2（b）或3（b）。
This paper discusses how the weld groove and the plate thickness affect the sheet metal manufacture processing, and how to design with reasonable method.
本文阐述了焊接坡口和板厚处理对钣金加工制造工艺的影响，并用合理的方式设计和处理。
Weld-seam position and thickness difference do not affect stress and strain states.
焊缝位置和壁厚差异变化时，拼焊管各区域的应力状态保持不变。
With wide range to adjust current, it can weld plates with various thickness.
电流调节范围宽，可适合多种板厚的焊接。
The influences of strength matching on fillet weld were analyzed. The relationships among fillet weld size, thickness of base metal and matching coefficient of strength were established.
分析了强度匹配对角焊缝设计的影响，建立了角焊缝焊脚尺寸与板厚，强度匹配系数之间的关系，讨论了强度匹配选择的依据。
Through quantitative and SEM analysis, the minim zinc was found remaining on the surface of weld and the zinc thickness on the heat-affected zones appeared gradient.
定量及SEM分析表明，焊缝中表面只残留少量锌，在焊缝两侧的热影响区，锌层厚度呈梯度分布。
The author strongly suggested that those centrifuges which has been servicing more than10 years, should be safety-checked on thickness, hardness and the weld of rotating drum.
提出了使用10年以上的离心机需对转鼓的壁厚、硬度、焊缝等进行安全检测的建议。
The plasma arc welding have a high energy density, thick welding thickness that can weld for single time.
等离子弧焊具有能量密度高，一次性可焊厚度大等优点。
If the surface of the stir pin is smooth, the migration of interface in the thickness direction reduces, but the interface spreading to the weld is serious.
若搅拌针表面是光滑的，搭接界面在厚度方向上的迁移减小，但返回边界面向焊缝中心延伸的程度增大。
As a result of anti-block thickness was not weld cross-section of smaller sizes, and carrying capacity is not strong;
由于防倒块厚度不大，焊缝截面尺寸较小，承载能力不强；
General note: the "thickness of weld metal" is the total weld metal thickness deposited by all welders and all processes in the test coupon exclusive of the weld reinforcement.
一般笔记：焊接金属的“厚度”是所有焊工和在测试优惠券的所有过程放置的总焊接金属厚度专属焊接增强。
Notethe coating thickness of weld seam should be not less than 80% of coating thickness on pipe body.
焊缝处的防腐层厚度，不得低于管本体防腐层规定厚度的80%。
Some Suggestions are carried out to define the thickness of cartridge, the local strengthening and the weld locations.
对弹体的壳体厚度、局部加固和焊接位置提出建议。
The influence mechanism of the thickness of the nickel coating on the steel side on tension-shear strength of the weld was studied by means of tension-shear tests, SEM and EDS.
借助拉剪试验、SEM和EDS，研究了搭接面低碳钢侧镀镍层厚度对接头拉剪强度的影响机制。
The weld size was controlled according to the definition of leg on the corner joint and DL/T869—2004 (power plant welding technical regulation), which led to the effective thickness was insufficient.
按目前大多数人认可的角接接头焊脚的定义，根据DL/T869—2004《火力发电厂焊接技术规程》去控制焊接尺寸，会出现焊缝有效厚度不足的问题。
In the evaluation of steel pipe quality, the pipe appearance, the weld appearance, the pipe wall thickness, the defect types and sizes, and the pipe materials are selected as the evaluation factors.
在钢管质量评价过程中，选取了钢管外观、焊缝外观、管道壁厚、缺陷种类及尺寸、管道材料作为评价因素集。
The results show that changes of weld-line shape and thickness ratio have significantly different effect on the formability of curvilinear-weld-line TWBs.
研究结果表明，焊缝形状以及厚度比对不同类型的曲线焊缝拼焊板成形性的影响程度明显不同。
A too narrow weld and any lack offusion are indicated by a series of intermediate echoes within the echosequence from the total thickness of the two welded sheets.
窄焊缝中的任何未熔合通过在两块薄板结合处低波之间出现的一系列中间回波被显示出来。
Seal welds shall be welded with half the thickness of the carrying fillet weld.
密封焊道应焊成现填角焊缝厚度的一半。
Seal welds shall be welded with half the thickness of the carrying fillet weld.
密封焊道应焊成现填角焊缝厚度的一半。
应用推荐