The difficult technical problems are solved due to the structure design improvement, local structure and weld position changes.
通过对其结构进行设计改进，改变局部结构及焊缝位置，解决了多年来工艺方面的难题。
Grinding weld position detection and identification algorithm was studied and the characteristic values of grinding weld were extracted.
研究了磨削焊缝位置检测和识别算法，提取了磨削焊缝特征值。
Welding pose includes weld position and torch orientation, which is represented by weld slope, weld rotation, torch work Angle and traveling Angle.
焊接位姿包括焊缝位置和焊枪姿态，可以用焊缝倾角、焊缝转角、焊枪工作角和焊枪行走角四个参数来表征。
For the even weld of crossover pipe pieces with reliable welding, the project requires to cut the weld position of crossover pipe pieces into shape exactly.
工程上，为了管件的相交处焊缝均匀，焊接可靠，需要将相交管件的焊缝处准确切割成型。
At the position of the weld, the inner side of the weld should be stopped.
在定位焊时焊缝内侧应停止充氩维护。
Weld-seam position and thickness difference do not affect stress and strain states.
焊缝位置和壁厚差异变化时，拼焊管各区域的应力状态保持不变。
In order to obtain the best gate location addition, the position of air bubbles and weld lines were forecasted.
预测可能存在的气泡、熔接痕的位置，确定最佳浇口位置，并在此基础上设计模具。
In order to obtain the best gate location addition, the position of weld lines and the clamp force were forecasted.
预测可能存在的熔接痕位置及锁模力的大小，确定最佳浇口位置。
During the welding process, the computer will modify the position of the electron gun based on the deviation to make the electron beam spot centered on the annular weld groove.
在焊接时利用处理后的偏差值在圆形焊缝相应位置不断修正电子枪的位置，从而达到电子束束斑与焊缝自动对中的目的。
According to the model of the welding position, giving a weld seam point, the weld orientation then can be resolved from the weld rotation Angle and the weld slope Angle.
根据焊缝位置的数学模型，得到了描述焊缝焊接位置的参数——焊缝转角和焊缝倾角与焊缝姿态的关系。
The Beamlet transform was introduced to detect the line segment characteristic of the structured light in the image to identify the position of the weld seam effectively.
为有效提取图像中结构光线性特征以确定焊缝位置，引入了束波变换。
In this system, welding robot can be guided to the initial welding position of any planar weld automatically by the aid of a charge coupled device camera.
在系统中，机器人可以在视觉系统的引导下自动定位到任意平面焊缝的起始位置。
C,. Incomplete fusion prevent adopting greater welding current, use correctly to weld the cleaning of operating, notice groove position.
未熔合的防止采用较大的焊接电流，正确地进行施焊操作，注意坡口部位的清洁。
Then using CAE analysis and through adjusting the gate position, weld lines can be optimized to the minimum length, and this result has also been identified by practice.
进而应用CAE软件进行分析，通过调整浇口位置，对熔接痕的长度进行优化，使其减少到最小，结果得到实践验证。
Special pattern was used to weld core iron to guarantee position accuracy of cast holes;
采用专用胎具焊接芯骨以保证铸孔的位置精度；
Automatically imitating a type to weld a special airplane can according to differently deal with contact of shape and position carry on imitating a type to weld.
自动仿型焊接专机可根据不同的接头的形状和位置进行仿型焊接。
The two jointing project is calculated and some results about the effecting of the amount and position of the weld in the jointing combination girder' s ability are achieved.
以自卸式汽车为例，对两种焊接方案和焊点直径影响进行对比，得出了焊点数量、布局等对焊接组合梁承载能力的影响。
The results show that post welding residual stress concentrates in the vicinity of two weld and the maximum residual stress appears in the starting position of TIG weld.
结果表明，焊接残余应力集中分布在两种焊缝附近，最大残余应力出现在TIG焊缝起焊位置。
The above symbols should be put in the proper position of film, and the distance from weld edge should be at least 5mm (see picture3).
上述定位标记和识别标记均应放在胶片的适当位置，并离焊缝边缘至少5mm(图3)。
This paper presented a practical system and method to guide the welding robot to the initial welding position of weld.
介绍了一种实用的视觉引导焊接机器人到初始焊位的导引系统和方法。
Leaving the disc in a fully closed position firmly closed also prevents weld spatter from falling directly onto the mating faces of the seat and disc.
保持阀瓣处于完全关闭位置也能够避免焊花直接掉在阀座和阀瓣的连接面上。
Ideal where mounting space is limited. Base can be drilled or weld. Clamps are supplied with a separate handle. The user welds handle in desired position and supplies required hold down bar.
在设计的安装位置上将夹钳焊接安装，并在理想的空间位置焊装手把并点焊固定与手把连接的头部，使其操作方便自如。
The runners of 6 operated generating unit of Ertan Hydro Station have been checked and no crack on the primary weld of the field welding position is observed.
二滩水电站已全部投运的6台机转轮经停机检查，现场焊接的主焊缝无裂纹。
In horizontal position welding, the gravity makes molten metal flow downward and sometimes causes weld defects such as undercut and overlap.
横向焊接时由于熔化金属重力的作用，会引起熔池金属下淌，从而产生咬边以及焊瘤等焊接缺陷。
Two groups of matching relation of the weld speed and the wire feed rate were found in a condition of invariable laser power and focus position.
前者试验获得了一定激光功率和离焦量条件下两组焊接速度和送丝速度的匹配关系，并发现填充焊丝的加入对焊缝咬边现象确有改善；
A special design of narrow gap SAW machine is developed in order to weld straight and circular joints at flat position.
研制了适合水平直焊缝和水平圆形焊缝的窄间隙埋弧焊专用焊机。
The drop simulation for the front plastic shell have been done with take the position of weld line which result from the two relatively optimal projects to the lowest location.
②塑料件前壳试验：将两组较优浇口方案产生的熔接痕位置调整到跌落方向的最低处。
In this paper, it has been realized the recognition for weld seam and its initial position in local environment with visual method.
采用视觉方法实现在局部环境中对焊缝及其起始点的识别。
In this paper, it has been realized the recognition for weld seam and its initial position in local environment with visual method.
采用视觉方法实现在局部环境中对焊缝及其起始点的识别。
应用推荐