In this paper the wear morphology of tool is analysed in detail and then concerned Suggestions are hereupon recommended.
本文详细地分析了刀具磨损的形貌后，提出了相应的建议。
The wear morphology is characterized by abrasive wear and adhesion wear with low current while it is characterized by adhesion with high current.
电流较小时具有磨粒磨损和粘着磨损的共同特征，电流较大时以粘着磨损为主。
They should not wear ties that do not match the "morphology of the face" nor socks with cartoon motifs.
职员佩戴的领带要“与脸型相衬”，不能穿卡通袜。
By using SEM to examine the worn surface morphology, the wear mechanisms of these coatings were explored.
通过用扫描电镜对磨损表面形貌进行的观察分析，探讨了复合涂料涂层的磨损机理。
The surface morphology of wear scar, nanoparticles and its element distribution have been tested and analyzed by scanning electron microscope(SEM) and energy dispersive spectrometry(EDS).
使用扫描电子显微镜（SEM）和能谱分析（EDS）等观察分析磨损钢球表面的磨痕形貌、化学元素和纳米粒子形态。
The worn surface morphology analysis shows that the wear of laser strengthened layers follows the plough trenches way caused by plastic deformation.
由磨面形貌分析可知强化层是以塑性变形引起的犁沟方式磨损的。
The quantity, composition and morphology of debris in machine oils are a reflection of wear modes and degrees of engine parts.
滑油中磨粒的数量、成分和形态反映着机器零部件的磨损形式和磨损程度。
The structure morphology the hardness and wear resistance of composite have been investigated, and fracture model of the composites has been analyzed.
考察了复合材料的组织形貌，检测了复合材料的硬度和耐磨性，分析了复合材料的断裂模式。
The mass loss after impact-wearing was measured, the morphology on the wear surface of the steel was analyzed by SEM, the microstructure was observed by OM.
对冲击磨损试验后试样进行了失重测量，并用SEM分析磨损表面形貌，用OM观察金相组织。
The influence of heating temperature on morphology of eutectic carbide and impact fatigue property of low alloy wear resistant cast iron were studied by OM, SEM and impact fatigue tester.
采用金相、扫描电镜和力学性能分析方法研究了加热温度对含稀土低合金耐磨铸铁冲击韧性的影响。
It is found that adding vanadium can refine the high-chromium cast iron matrix, change the carbide morphology and distribution, improve the hardness and wear resistance of high chromium cast iron.
结果表明，钒的加入可显著细化高铬铸铁的基体组织，改变了碳化物的形态及分布，提高了高铬铸铁硬度及耐磨性能。
The results show that alloying elements and rare earth can refine grain, change carbide morphology and distribution, and increase mechanical properties and wear-resistant properties.
结果表明，合金元素能够细化晶粒，改善碳化物的形貌和分布，提高力学性能和耐磨性。
The mechanical properties, wear properties and micro-morphology of the prepared blend were studied.
并对共混物的力学性能、磨耗性能及微观形态进行了研究。
The results show that the grain is fined, the morphology of reticulation carbides is improved, the hardness and wear resistance of casting high speed steels are also enhanced by modifying treatment.
研究了热处理工艺对铸态和变质处理铸造高速钢组织与性能的影响。
And then according to the constituents and construction morphology, the main reasons why Zn-Al alloy has good wear property are analyzed.
并结合锌铝合金的成份和组织结构特点，分析了具有良好耐磨性的主要原因。
The morphology of ZA 27 alloy reinforced by re compounds and its wear resistance were studied.
对稀土化合物增强ZA27合金的组织及耐磨性做了研究。
The morphology of ZA 27 alloy reinforced by re compounds and its wear resistance were studied.
对稀土化合物增强ZA27合金的组织及耐磨性做了研究。
应用推荐