In the final analysis, overloading your washing machine can have a number of negative consequences.
在最终的分析中，洗衣机的超负荷对衣服会有许多负面的结果。
Laboratory study on preparing potassium sulfate from the Washing Liquor of salt slurry is introduced. Its feasibility is described through the analysis to phase diagram and experiment.
通过以盐浆洗液为原料制取硫酸钾的实验研究，并通过相图分析和实验论证了该工艺的可行性。
The washing machine design, washing technological process, the machine structure and principle were introduced. The analysis and computation to the machine parameters and power were made.
本文介绍了环带式搅龙葡萄干清洗机的设计依据、清洗工艺、结构和工作原理，并对环带式搅龙的参数和功率进行了分析计算。
According to the analysis of sewage quality, reform is carried out for the water refined unit to realize recovery of washing water and analysis water in this unit.
通过对污水水质的分析，对精制水单元工艺流程进行了改造，实现了该单元冲洗水及分析水的回用，达到了节能减排的效果。
Bitumen a, group component and light hydrocarbon analysis is the effective analytic way for evaluating reservoir water flooding and washing degree.
沥青a、族组分分析和轻烃分析是评价油层水淹、水洗程度的有效分析方法。
Through the analysis of the washing pulps in demolition pulping, a productive experiment on the forage yeast from washing pulps was carried out.
该文通过爆破法制浆洗浆液的成分分析测定，对洗浆液进行了饲料酵母的生产性试验。
The article gives an analysis on present situation of coal washing, clarifies the necessity to give a reform on present floatation and pressure filtration system.
通过对洗煤现状的分析，阐述了洗煤浮选、压滤系统改造的必要性。
According to experiments and analysis of variance, the optimum prevention methods are daubed by using solution of Sanwei washing powder and pharmaceutical preparations of pepper.
根据试验和方差分析，最好的防治方法是应用“三威洗衣粉液”和“辣椒制剂”进行涂抹。
In this article we determined the optimal condition, i. e. washing time temperature and the base's density, about the base washing by using the method of the factor analysis and quadrate experiment.
利用单因素分析法和正交实验法确定了碱洗的最佳条件，包括碱洗时间、碱洗温度和碱洗浓度等。
The rapid analysis method of welding quality, acid washing test, for the longitudinally high frequency welded pipe is introduced.
介绍了一种快速分析高频直缝焊管焊接质量的方法——酸洗试验。
Abstract: Designed a one-mode two-cavity injection mold through the analysis of the handle of washing machine.
摘要：通过对塑料洗衣机把手工艺的分析，设计了一副一模两腔的注塑模具。
In accordance with downhole tubing sticking by sand burial accident, this paper proposes hollow rod sand washing after analysis of downhole string structure and hydraulic calculation of sand grain.
针对处理井下油管砂埋遇卡事故作业中出现的技术问题，在分析井下管柱结构及砂粒的水力计算的基础上，提出了空心抽油杆冲砂工艺处理措施。
This paper introduces the method, analysis and result of tail slime water flocculating test in the outside of washing plant in Guanshan Coal Mine.
介绍了冠山矿洗煤厂厂外尾煤泥水絮凝试验的方法、结果和分析情况。
Based on the analysis of the structure characteristics of wave wheel of washing machine and the mould design project, an injection mould for this part was designed.
通过对洗衣机波轮轴承的结构特点与模具设计方案的分析，介绍了洗衣机波轮轴承注塑模的结构与工作过程。
According to the several analysis of front chapter, I propose two localization motion that washing machine design, and has done the corresponding localization design.
第五章根据前面几章的分析，提出了两个本土化洗衣机设计的提案，并做了相应的本土化设计。
Through the analysis of membrane fouling mechanism, using the appropriate chemical cleaning methods, the loss of membrane flux of 50% could be recovered after repeated washing five times.
通过对膜污染机理的分析，采用相应的化学清洗方法对膜进行清洗，重复清洗5次后仍然可以恢复损失膜通量的50%以上。
During the trace analysis, selection of container material and washing-up method is very critical for getting accurate analysis result.
在痕量分析中，为获得准确的分析结果，容量材质以及洗涤方法的选择至关重要。
Because the universal processes of film preparing, washing, drying and re-dissolvingwere simplified, the analysis time was reduced substantially.
简化了通常测定过程中的压膜、烘干、重新溶解等步骤，明显缩短了测定的时间，更能适合于现场分析。
Methods: The final water washing method was used to conduct sampling analysis.
方法：采用最终淋洗水法取样分析。
The article mainly introduces the working principle of the continuously circling grain-washing machine and its structural design of the main components as well as the analysis of the experiments.
本文主要介绍循环连续洗米机的工作原理和主要工作部件的结构设计及其实验分析。
The invented cleaner for suction heads is used for automatic washing of the suction heads of sampler in batches in hospital analysis department or laboratories.
本发明属医疗器械，用于各医院检验科以及其他实验室微量加样器吸头的大批自动清洗。
Through the analysis of the drain valve of washing machine, an injection mould for the drain valve was designed.
通过对洗衣机排水阀塑料件的分析，设计了洗衣机排水阀注塑模。
Based on the analysis of the structure characteristics of the water inlet of a washing machine, an injection mould for the water inlet is designed.
前言：通过对洗衣机进水口塑件结构特点的分析，设计了洗衣机进水口注射模。
Through regression analysis in 1983, the positive correlation was associated with 3 factors; no hand-washing before meal;
逐步回归分析1983年饭前不洗手、不吃蒜、经常吃零食3个因素呈正相关；
Through regression analysis in 1983, the positive correlation was associated with 3 factors; no hand-washing before meal;
逐步回归分析1983年饭前不洗手、不吃蒜、经常吃零食3个因素呈正相关；
应用推荐