This may require using a high current switch card for sourcing and a low voltage switch card for measuring.
这就可能需要利用一个大电流开关卡来提供电流，一个小电压开关卡用于测量。
The highest voltage a switch card can withstand reliably is the maximum volt age specification, which is determined primarily by the relay specification.
开关卡能够可靠承受的最高电压即为最大电压指标，它主要是由继电器的技术指标决定的。
To prevent damage to the switch card, verify that the product of the maximum current and maximum voltage does not exceed the power rating of the switch card.
为防止损坏开关卡，需验证最大电流和最大电压的乘积没有超过开关卡的功率额定值。
The contact potential or thermoelectric offset voltage is the key specification of a switch card designed for low voltage switching.
接触电势或热电效应偏移电压是设计用于低压切换的开关卡的关键技术指标。
"Maximum signal levels" refers to the highest levels of voltage, current, and power that can be switched without damaging the switch card.
“最大信号电平”是指能够切换但又不会损坏开关卡的电压、电流和功率的最大值。
Finally, combining programming measurement software together with data-requiring card and potential transformer circuit complete the measurement of three-phase voltage fluctuation and flicker.
最终混合编程检测软件、数据采集卡、电压互感器电路共同完成对电网三相电压波动和闪变的检测。
The card can collect four axes' encoder pulse signals simultaneously, and control servo motor by four output analog voltage. Furthermore, it can control input and output I/O signals.
该运动控制卡能同时采集四轴的编码器脉冲信号，输出四路模拟电压控制伺服电机，同时能控制I/O信号的输入和输出。
The hardware is made up of Data Acquisition card (DAQ) and signal conditioning extension for instrumentation (SCXI) which is composed of Hall voltage current sensor.
系统的硬件平台主要由数据采集卡和霍尔电压电流传感器构成的信号调理器组成。
The hardware of the system mainly consists of a ZHJ-1B current sensor, a self-made resistance strain force sensor , the device for measuring electrode voltage and a NI-DAQ 6062E data acquisition card.
系统的硬件主要有：ZHJ-1B型电流传感器、自行研制的电阻应变式力传感器、电极间电压测量装置及NI-DAQ 6062E数据采集卡等。
The grinding temperature is obtained online using thermoelectric couple, voltage amplifier, A/D card and data collection software.
利用铁-康铜热电偶丝、电压放大器、A/D板通过半人工热电偶测温方法在线采集磨削温度；
Switch card specifications are usually stated with a specific application in mind, such as low current or high voltage switching.
开关卡的技术指标通常是由特定的应用决定的，例如小电流或高电压切换。
The thermoelectric offset voltage due to the switch card and the interconnecting cable may be compensated for by using a short-circuited channel to establish a zero reference.
由于开关卡和互连电缆引起的热电效应偏移电压可采用一个短路通道来建立一个零参考，从而进行补偿。
Method of calculation for the non-contact IC card chip coupling power supply and the read and write distance were analyzed, and the relative low-voltage circuit designs were introduced.
分析了非接触式IC卡芯片耦台电源及读写距离的计算方法，并简要介绍了相关低压电路的设计技术。
These major changes in voltage, core clock and memory clock can easily destabilize a card to a point where you get artifacting and even a lockup.
这些在电压、核心时脉和记忆体时脉的改变，容易造成显卡的不稳甚至当机。
The system select W78LE516 MCU and CPLD to construct the control circuit and use quickly read and write low power consumption, low-voltage external data memory CF card to save the signal.
系统选w 78le516单片机和CPLD来构造控制电路，用读写速度快、功耗低的低电压外部数据存储器CF卡存储采集完的信号。
The system select W78LE516 MCU and CPLD to construct the control circuit and use quickly read and write low power consumption, low-voltage external data memory CF card to save the signal.
系统选w 78le516单片机和CPLD来构造控制电路，用读写速度快、功耗低的低电压外部数据存储器CF卡存储采集完的信号。
应用推荐