Define your virtual Ethernet devices (HMC).
定义虚拟以太网设备(HMC)。
Define your virtual Ethernet devices (VIO).
定义虚拟以太网设备(VIO)。
Method 2: Integrated virtual Ethernet (IVE).
方法2：集成虚拟以太网(IVE)。
Step 3: Assign the virtual Ethernet ID to a physical adapter
步骤3：把虚拟以太网ID分配给物理适配器
Figure 5 depicts the example with the addition of a two virtual Ethernet LANs.
图5展示的是添加了两个虚拟以太网lan的示例。
Virtual Ethernet provides roughly the same function as a 1 Gigabit Ethernet adapter.
虚拟以太网提供了与1Gigabit以太网适配器大致相同的功能。
Figure 4 shows that the LPAR is configured with virtual Ethernet and virtual SCSI adapters.
图4显示这个LPAR配置了虚拟以太网和虚拟scs i适配器。
The enablement and setup of virtual Ethernet does not require any special hardware or software.
建立和设置虚拟以太网不需要任何专门的硬件或软件。
Each partition can have up to 65,534 virtual Ethernet adapters connected to the virtual switch.
每个分区可以有最多65,534个虚拟以太网适配器连接到虚拟交换机上。
Add a virtual disk definition unit and a virtual Ethernet connection unit to the virtual image.
向虚拟化镜像添加一个虚拟的硬盘定义单元和一个虚拟的以太网连接单元。
If you recall, you tried to change an adapter earlier that was configured with virtual Ethernet.
如果您回想一下，您以前应该尝试过更改使用虚拟以太网配置的适配器。
The screen shot of the second virtual Ethernet adapter for the VIO Servers should look the same.
VIO服务器的第二个虚拟以太网适配器的屏幕截图看上去完全相同。
The VIO client LPARs are told which virtual Ethernet adapters they should use for their communication.
告诉VIO客户机LPAR应该使用哪些虚拟以太网适配器进行通信。
The second virtual Ethernet adapter on each of the VIO Servers must be configured as a non-trunk adapter.
必须将每个VIO服务器上的第二个虚拟以太网适配器配置为非干线适配器。
When VIO servers are created, they are assigned both physical Ethernet adapters and virtual Ethernet adapters.
在创建VIO服务器时，分配物理以太网适配器和虚拟以太网适配器。
Virtual I/O Server hosts logical I/O devices to the partitions, such as virtual SCSI disks and virtual Ethernet.
虚拟I/O服务器将逻辑 I/O设备分配给分区，如虚拟SCSI磁盘和虚拟以太网。
When configuring the profiles of the VIO Servers on the HMC, create two virtual Ethernet adapters on each server.
在HMC中配置VIO服务器的概要时，在每个服务器上创建两个虚拟以太网适配器。
After you enable a specific virtual Ethernet for a partition, a network device named ethXX is created in the partition.
当您为某个分区启用了一个具体的虚拟以太网之后，在那个分区中就会创建出一个名为ethxx的网络设备。
You should also set up a third virtual Ethernet adapter on each VIO Server using the virtual LAN ID of the trunk adapter.
您还应该在每个VIO服务器上设置第三个虚拟以太网适配器，使用干线适配器的VirtualLANID。
This is required in order for the virtual Ethernet devices to access the physical Ethernet adapter and the external network.
这是为了让虚拟以太网设备能够访问物理以太网适配器和外部网络。
Then, the VIO client LPARs are told the virtual Ethernet adapters and VLAN Numbers they should access through an SEA mapping.
然后，通过sea映射告诉VIO客户机LPAR应该访问的虚拟以太网适配器和VLAN编号。
You define virtual Ethernet and disk devices on the VIO Server and then make them available to the other LPARs on the system.
您在VIOServer上定义虚拟以太网和磁盘设备，然后使它们对系统上的其他lpar可用。
This is a very typical use of virtual Ethernet, because the communication is very fast and no additional hardware is required.
这是虚拟以太网的一个非常典型的应用，因为通信速度非常快，而且不需要任何另外的硬件。
Check the attributes of the virtual Ethernet adapters with the lsdev -dev entX -attr command to confirm which adapters are which.
用lsdev—deventx—attr命令检查虚拟以太网适配器的属性，确认适配器的映射关系。
Create a dependency link from the virtual Ethernet connection unit in the virtual image to the L2 connection in the physical server.
创建一个从虚拟镜像中的虚拟化以太网连接到物理服务器中l2连接的依附性链接。
From this menu you can see the virtual Ethernet adapter we created previously with the 383 primary VLAN and the 373 additional VLAN.
在这个菜单上，可以看到前面创建的虚拟以太网适配器（主VLAN 为 383，辅 VLAN 为 373）。
In most cases, however, you will want to allow partitions connected to a virtual Ethernet to also communicate with the physical network.
不过，在大部分情况下，您需要连接到虚拟以太网的分区也能够与物理网络进行通信。
The TAP driver allows the guest operating system to read or write raw Ethernet frames to a virtual Ethernet device (extended to user space).
TAP驱动程序使访客操作系统能够将原始以太网帧写到一个虚拟以太网设备(用户空间的扩展)。
Virtual Ethernet: Virtual Ethernet allows for inter-partition - and IP-based communications between logical partitions on the same frame.
虚拟以太网：虚拟以太网支持在同一个大型机上的逻辑分区之间进行基于内部分区和基于IP的通信。
A gratuitous ARP request is sent on all virtual Ethernet adapters to update the ARP caches on all external switches and systems on the network.
一个ARP请求被发送到所有虚拟以太网，从而更新网络上所有外部交换机和系统上的ARP缓存。
应用推荐