In order to solve the problem, the main causes of vibration error were analyzed.
为了解决该问题，振动误差的主要原因进行了分析。
The problem of slender pieces deformation and the vibration error is one of the key techniques that whirling should solve when using in finish machining.
旋风铣削法是一种较先进的高效率加工螺纹方法 ，适用于批量较大的螺纹粗加工。
Barrel type straight spindle: spindle and spindle motor to reduce the transmission link error and vibration, the use of integrated direct design, and the use of high precision ABECT.
弹筒式直结主轴：主轴与主轴马达为减少传动连结所产生的误差与震动，采用一体式直接设计，并采用高精密abect。
The medium vibration during solving process is a noise rather than a more real simulation to medium mechanical behavior and could cause calculation error for elastoplastic medium.
求解过程中的介质振动，是一种噪音，可引起弹塑性介质计算结果误差，而弹性介质的计算结果几乎不受影响。
A new type of linear vibration table is brought forward, whose application to INS error model parameter separation is investigated.
本文提出了一种新型线振动台，探讨了将其用于惯导平台误差模型参数分离的可行性。
The vibration characteristics of external plunge grinding and the ground surface profile error are investigated through experiments analysis.
在实验的基础上，对磨削过程振动特征以及由此产生的磨削表面形貌误差进行研究。
Aimed at the characteristic of bigger error existed in active vibration control model of frame structures, experimental modes data are usually used to modify calculating model.
针对框架结构振动主动控制模型误差较大的特点，通常采用试验模态数据来修正计算模型。
The vibration of the nonlinear pendulum is studied by means of linearization and correction method, the curves of the period ratio and the relative error is plotted.
应用线化和校正方法，研究了单摆的非线性振动，作出了周期比和相对误差随摆角的变化曲线。
This article selects from the FOG's structural material, the fiber optical link size estimates, as well as the FOG system error origin embarks under the vibration situation.
本文从陀螺结构材料选取，光纤环尺寸估算，以及光纤陀螺在振动的情况下系统误差的来源出发。
For dissociation energy, zero point vibration energy (ZPVE) is calculated and basis set superposition error (BSSE) is corrected by counterpoise method.
解离能计算进行了零点振动能(ZPVE)校正，并运用完全均衡校正法对基函数重叠误差(BSSE)进行校正。
This paper analyses the special dynamic behavior of entering drilling of micro drill with vibration in the direction of axis and its correction function to location error of entering drilling.
分析了微小孔钻头轴向振动入钻时特殊的动力学行为及其对入钻定位误差的修正作用。
In this system, the variable frequency motor is applied to meet the requirement of low speed to check the compositive error and high speed to measure the vibration.
针对检测综合误差和振动时对主轴转速的要求，采用变频电机来控制主轴转速，以满足系统对转速的要求。
For vibratory gyro, very small coupling error will induce great measuring error because driving vibration is much greater than sensing vibration.
由于驱动振动幅度远大于读出振动，因此极小的耦合量就会造成很大的检测误差。
The main cause to create harmonic error are the relative vibration in system, in stability of geometry configuration, random disturbance and in sufficient feeding ability of the machine tool.
谐波误差产生的主要原因是系统相对振动、几何布局失稳、随机干扰和机床进给能力不足。
The vibration frequency of box gird is usually calculated by the elementary beam theory, but it will lead to a large error because of the existence of shear lag effect and shear deformation.
由于剪力滞效应及剪切变形的存在，箱梁的弯曲振动频率按照初等梁理论计算往往存在较大的误差。
Marine diesel is simulated by the upper mass of the system. Proper positions of secondary vibration source are chosen and some points on the lower mass are chosen for error evaluation.
以双层隔振系统的上层质量来模拟柴油机，在下层质量上合理地布置次级振源，选取合适的误差评价点，针对这些点的振动响应实施控制。
Simulated the wire vibration using finite element analysis software ANSYS, which has few error.
利用有限元软件ANSYS模拟电极丝振动，得到了理论计算与ANSYS模拟的误差值。
The relative error of displacement measurement is less than 1% in comparison with that measured by a reference vibration platform.
与振动台的试验对比，位移测量相对误差小于1%。
As for some of the unsteady vibration signals of diesel engine, false result may be provided by using Fourier analysis, thus error diagnosis would be induced.
传统的振动分析常采用傅立叶分析法，对于柴油发动机某些非平稳振动信号，傅立叶分析可能给出虚假的结果，从而导致错误诊断。
The application of the Extended Kalman Filter (EKF) to identify INS platform drift error coefficients under the condition of ideal and nonideal linear vibration is presented.
设计了多位置测漂方案，利用扩展卡尔曼滤波对理想、非理想线振动条件下的参数辨识问题进行仿真。
The torsional vibration method is an effective method to measure bullet rotary inertia, the key of which is the cor-responding error analysis.
扭振法是测量弹体转动惯量的有效方法，其误差分析是关键。
An adaptive bandwidth solution to the problem of the bit error rate (BER) increasing with the vibration increasing has been presented.
针对比特误码率(BER)随振动幅值增加而上升的问题提出了用带宽自适应方法控制的解决方案。
The measurement error of Coriolis mass flow meter is based on the vibration characteristics of the elastic tube of flow meter.
弹性测量管的振动特性决定了科氏质量流量计的测量精度。
The bit error rate of an atmospheric laser communication system is affected by not only vibration amplitude but also the aperture of optical transmitting antenna.
大气激光通信系统的误码率不仅受到振动时振幅大小的影响，而且受到光学发射天线孔径的影响。
The quality of fixture design will directly affect the vibration test error.
夹具性能设计的好坏将直接影响到振动试验的成败。
It was shown that the conic error can be compensated by two-sample iteration algorithm with high-frequency vibration. The precision of SINS can be improved by coning compensation.
结果表明，二频机抖激光陀螺在振动条件下的圆锥误差可以通过双子样迭代算法补偿，提高了捷联惯导系统的精度。
The simulation experiment shows that the system has better performance of vibration suppression control and stronger robustness for modeling error of load inertia moment.
仿真实验表明，该系统具有良好的防振控制性能，而且对负载惯性矩的模型化误差具有较强的鲁棒性。
A control method to initiatively improve turning quality based on ultrasonic vibration cutting and error compensation technologies is proposed, and experiments have proved that this method can...
提出了以超声振动切削和误差补偿技术为基础的提高车削质量的积极控制方法，实验证实了该方法能全面地提高加工件的加工质量。
Installation and assembly clearance error caused by the vibration of the pump body is an important reason.
安装及装配间隙误差是造成泵体振动的重要原因。
In a system of space optical communication, it will influence to bit error rate of the communication system when the optical transmitter wiggles as vibration of the satellite's platform.
在空间光通信系统中，由于卫星平台的振动，使得光发射机发生摆动，从而对通信系统的误码率产生影响。
应用推荐