Compressors are run up with the anti surge valve fully open.
压缩机在启动时防喘振阀全开。
Put into operation, let control valve fully open, so the media after a fixed period of time to run into deformity.
投运前，让调节阀全开，让介质固定一段工夫后再纳入畸形运行。
Screw pump should be in suction stop valve fully open under the condition of starting, in case of overload or empty.
螺杆泵应在吸排停止阀全开的情况下起动，以防过载或吸空。
The installation 1, Qudiao flange end of the Flange-connection fixed ball valve protective cover on both sides, in the valve fully open state to wash clean.
安装1、取掉法兰端两边的保护盖，在阀完全打开的状态下进行冲洗清洁。
Compressors are run up with the anti surge valve fully open. This valve is forced to remain open, independently of the control system, until the run-up PROCEDURE has been concluded.
压缩机升速时防喘振阀全开，该阀不受控制系统控制而被强制保持打开直到升速阶段完成。
Ball valve fully open, the flow resistance is very small, almost zero, so the ball valve diameter is widely used in petroleum and natural gas pipelines because the pipeline cleaning easy.
球阀在完全开启时，流阻很小，几乎等于零，因此等径球阀广泛应用于石油天然气管线中，因为容易清扫管线。
Open valve fully to its memory setting and, on a piece of paper, record the valve setting.
将阀门完全开启到它的记忆设置点上，在一张纸上，记录这个阀门设置。
Open the valve fully to its memory setting and, on a piece of paper, record the valve setting.
将阀门完全开启到它的记忆设置上，在一张纸上，记录阀门设置。
Open vent needle valve fully until dripping from vent connection stops.
完全开启排气针形阀直到从排气连接处的滴漏停止为止。
Be sure that valve is fully open. Apply heat to tube first. Transfer as much heat as possible through tube into valve. Avoid prolonged heating of valve itself.
要确保阀门处于开启状态。先对管道加热。尽可能多的将热从管道传递到阀门。避免延长阀门本身的加热时间。
Fully open the valve of inlet part.
全开入口段的阀门。
Should be fully open before the start of suction and discharge pipe valves, non-closing valve started.
启动前应全开吸入和排出管路中的阀门，严禁闭阀启动。
The factors stated are based upon a fully open valve.
这里所述的流量系数是指阀门全开时的流量系数。
Should be fully open before the start of the suction and discharge pipe valves, non-closing valve to start.
启动前应全开吸入和排出管路中的阀门，严禁闭阀启动。
Recommended Opening Procedure: The diaphragm valve handwheel rotates about 1 1 /4 turns from fully open to closed.
推荐的开启程序：从彻底打开到关闭，隔膜阀手轮旋转大约11/4圈。
With the regulator adjusting knob turned fully counterclockwise, place both hands on the cylinder valve and open it slowly, allowing the pressure to rise gradually in the regulator.
调整器的调节钮逆时针旋死后，两只手放在钢瓶阀门上，慢慢地开启，使调整器内的压力逐渐增加。
As the system responds to control, it can position the valve anywhere from closed to fully open.
在干蒸汽加湿系统对控制作出响应时，可以把调节执行器置于从关闭到全开的任何位置上。
The lowest % DFR circuit valve is the index valve and will remain in the fully open position.
最低%D FR回路阀是指标阀，将保持在全开的位置。
When the high-pressure gauge indicates maximum pressure, open the cylinder valve fully.
当高压量表指示为最大压力时，彻底打开钢瓶阀门。
When the valve is fully open, flow capacity is big, pressure loss is small, and the medium would not deposit in the body cavity.
全开时阀门流通量能力大，压力损失小，且介质不会沉积在阀体中腔。
Before taking a flow measurement reading, set the valve to its fully open (4.0) or at a preset position.
在获取流量测量读数之前，将阀门设置在全开(4.0)或在一个预调的位置。
Be sure that valve is fully open.
要确保阀门处于开启状态。
Be sure that valve is fully open.
要确保阀门处于开启状态。
应用推荐