If you do not specify a server in the "specify Transport" setting, the test connection USES the SRV record to find the server.
如果您不指定服务器，“指定传输”设置中测试连接使用SRV记录来查找服务器。
If "bindings then client" transport mode is chosen, channel exits will only be driven if the bindings mode connection fails.
如果选择“绑定然后客户端”传输模式，则仅在绑定模式连接失败时，才驱动通道出口。
It USES a single transport connection for sending and receiving the response, as shown in Listing 4 below.
它使用一个传输连接同时发送和接收响应，如下面的清单4所示。
Both connection factories should also be changed to use BINDINGS as the transport type.
这两个连接工厂都还应该更改为使用BINDINGS作为传输类型。
The connectors "map" to the available transport types and the modes of connection.
连接器 “映射”到可用的传输类型和连接模式。
But since a different transport connection is used to retrieve the response, the request and response need to be correlated.
但因为使用了其他传输连接来获得响应，因此需要将请求和响应关联起来。
This is because the transport connection might timeout before the response is available.
原因是在响应可用之前，传输连接可能会超时。
After the transport connection has been established, the Bluetooth client needs to issue the connect operation.
在传输连接已经建立之后，蓝牙客户机需要发出CONNECT操作。
To make use of a channel exit, an MQ messaging provider connection factory or activation specification must have a transport type of "client" or "bindings then client."
要使用通道出口，MQ消息传递提供程序连接工厂或激活规范必须具有传输类型“客户端”或“绑定然后客户端”。
An output port simplifies how you administer the transport details for a deployed sender bean such as connection factory and one or more destinations.
输出端口将对已部署的发送方bean的传输细节的管理进行简化，例如连接工厂和一个或多个目的地。
operation tells if a separate transport connection is to be used for sending the request and receiving the response.
setTransportInfo()操作的 Boolean 参数指出是否要使用不同的传输连接来分别发送请求和接收响应。
A transport mode of "bindings then client" can be selected when creating or modifying a WebSphere MQ messaging provider activation specification or connection factory.
创建或修改WebSphereMQ消息传递提供程序激活规范或连接工厂时，可以选择“绑定然后客户端”传输模式。
Ordinary JMS clients (even server side) will need to specify the InboundSecureMessaging transport on the connection factory panel.
普通的JMS客户端(甚至服务器端)需要在连接工厂面板指定InboundSecureMessaging传输。
Although Sandesha handles acknowledgements sent in the same transport connection, it does not support application responses sent in the same transport connection.
尽管sandesha会处理在同一个传输连接中发送的确认信息，但不支持在同一个传输连接中发送的应用程序响应。
HTTP transport that now supports both 1.0 and 1.1 for more efficient use of underlying TCP connection.
HTTP传输现在同时支持1.0和1.1，可以更有效地使用底层TCP连接。
This provides a synchronous invocation (blocking client with single transport connection) paradigm to the clients.
此组件提供一个客户机的同步调用(使用单个传输连接阻塞Client)范型。
Since both of the above approaches use a single transport connection to send and receive messages, they are not suitable for long-running transactions.
因为上面两个方法使用一个传输连接来发送和接收消息，所以这些方法不适合长时间运行的事务。
Because the bindings mode connection USES Shared memory, there is no overhead associated with transport over a network connection.
因为绑定模式连接使用共享内存，所以不存在与网络连接上的传输关联的开销。
Non-blocking single transport pattern: in this invocation pattern, you achieve a non-blocking call using only a single transport connection underneath.
非阻塞单传输模式：在此调用模式中，只使用下面的一个传输连接获得非阻塞调用。
The only way to reach the abandoned village are your feet or own wheels. Preferably, jeep wheels as there is almost no transport connection.
唯一能到达这个废弃的村庄只能依靠步行或者自行车。切勿使用吉普车，这儿几乎没有行驶线路。
There are a number of typical scenarios where a connection between services can utilize JMS as a transport: e-government, e-business, or industrial manufacturing are a few examples.
有很多典型的场景，其中服务间的连接可以使用JMS 进行传输：电子政务、电子商务或工业制造就是其中的一些例子。
The second semantic meaning of this URI applies when the original transport-specific back channel is not available (for example, the connection was broken).
此URI的第二个语义含义则是在原始传输特定回发通道不可用时发挥作用（例如，连接已断开时）。
The transport parameter is also required and tells JMS whether to use a client or bindings mode connection. When client mode is used, the host, chan and port parameters must be specified
传输参数也是必需的，它通知JMS是使用客户机模式连接，还是使用绑定模式连接。
A user data constraint establishes a requirement that the constrained requests be received over a protected transport layer connection.
用户数据约束(user data constraint)满足了受限的请求应该经由受防护的传输层链接进行传输的需求。
If the bindings-then-client transport mode is chosen, channel exits will only be driven if the bindings mode connection fails.
如果选择了bindings - then - client传输模式，那么只有在绑定模式连接失败时才使用通道出口。
And if the Web Service client needs to have non-blocking (still with single transport connection), then the client should use AsyncCall instead of Call.
如果Web服务客户机需要非阻塞调用(仍然使用单个传输连接)，则Client应该使用AsyncCall，而非Call。
Error processing can include general security related issues as well as SOAP transport-related issues; for example, Web Service Connection Parse Failed.
错误处理可以包括通常的安全性相关问题以及SOAP传输相关问题，例如，Web服务连接解析失败。
In order to make use of a channel exit, a WebSphere MQ messaging provider connection factory or activation specification must have a transport type of either client or bindings-then-client.
为了利用通道出口，WebSphereMQ消息提供程序连接工厂和激活规范的传输类型必须为client或bindings - then - client。
An invalid operation was attempted on an active transport connection.
试图在活动传输连接上运行无效的操作。
An invalid operation was attempted on an active transport connection.
试图在活动传输连接上运行无效的操作。
应用推荐