The Earth torque is one example, where the magnetic s Pole is tugged back each day, creating more stress on the plates in the Pacific and allowing the Atlantic to widen.
一个例子就是地球的转矩，地球的南极磁场每天都被拖回此处，造成了太平洋板块更多的压力，让大西洋延伸了。
Maxwell stress method is an available one to calculate electromagnetism torque of machines.
麦克斯韦应力张量法是计算电机电磁转矩的有效方法。
The research result states that the contacting stress, thread torque and thread joggle geometry restriction are mechanical points of the sticky thread.
研究结果表明：接触应力、上扣扭矩、螺纹啮合时的几何约束，是齿面粘扣的力学要点。
A magnetorheological (MR) clutch is a device to transmit torque by the shear stress of MR fluids.
磁流变离合器是通过磁流变液的剪切应力传递转矩的器件。
The definition of rated static torque for linear rolling guide is given according to the criterion for maximum contact stress.
基于最大接触应力的判据，提出滚动直线导轨额定静力矩的基本定义，并计算了几种产品的额定静力矩。
Rod strings are designed by computing compound stress with the fourth strength energy on the condition of torque and axial force.
应用第四强度理论，求解杆柱在扭矩和轴向力条件下的复合应力，设计抽油杆柱。
The transient dynamic analysis researched the dynamic stiffness and strength of the joint by investigating the maximum stress and strain when it transmits torque.
瞬态动力学分析通过考察联轴器传递转矩过程中的最大应力、最大位移及其发生部位来分析联轴器的动态刚度和强度状况。
In this work, the direct normal stress and the stress produced with torque wrench were applied on such transducers.
本文用直接外加法向应力和用力矩板手加应力两种方法测量在不同压力下压电换能器材料的应力与应变关系。
AIM: to investigate the effects of torque force load on the stress distribution in implant bone interface, so as to help the clinical selection of implant location.
目的：研究扭转力载荷对支抗种植体骨界面应力分布的影响，以指导临床正确选择支抗种植体的植入部位。
Performance characteristic and stress condition were analyzed in the process of progressive cavity pump well startup and a startup torque dynamic model was established.
对启动过程中单螺杆泵的运动特点和受力情况进行分析，建立了该系统启动扭矩动力学模型。
Corresponding load and torque were applied on the 3 different models according to different conditions to obtain the stress changes of the intervertebral disc that happened to the adjacent segments.
并根据不同工况对这3种模型施加相应的预载荷及扭矩，分析比较不同腰椎轴向运动时相邻节段椎间盘应力的变化情况。
The bending moment diagram and circle of stress are drawn; the most flexural torque and primary stress are solved in MATLAB.
利用MATLAB绘制剪力图、弯矩图、应力圆以及求解最大弯矩和主应力。
Based on three dimensional finite element analyses of magnetic fields, the cogging torque of a prototype motor is calculated using the virtual work and Maxwell stress tensor methods.
在电机内磁场三维有限元数值分析的基础上，采用虚位移和麦克斯韦张量两种不同的方法计算了电机的脉动转矩。
Based on the stress performance of steel pole of transmission line, the steel pole is simplified as a matter of cross bending and torque with variable sections and complex loads.
根据输电线路钢管杆的受力特点，将钢管杆简化成受复杂载荷作用的变截面梁的纵横弯曲和扭转问题，并采用传递矩阵方法进行分析求解。
Aiming at this practical request, the factors of effect on automotive steering torque are analyzed according to the steering torque that is got from the stress analyzing of the steering gear.
针对这一应用要求，根据汽车转向机构的受力分析得到的转向力矩，对影响汽车转向力矩的主要因素进行了分析，并具体对与向心加速度有关的部分转向力矩的实验曲线用最小二乘法进行了解析式拟合。
Exact torque control also reduces the risk for stress being built into the restoration and prevents component fractures.
准确的扭矩控制还能减小修复性手术压力过大的风险，并防止设备断裂。
The calculation is so complex as it is done according to torque principle that the inner stress acquired is often vulnerable to mistakes, and therefore must be checked.
按有矩理论计算由于计算较复杂，得到的内力往往容易出错，因而必须进行内力校核。
Varying speeds and loads causes torque multiplication and extreme stress on gears and bearings.
不同的速度和负载扭矩的原因乘法和极度紧张的齿轮和轴承。
The paper analyzed the bolt pre-stress affected to the mine roadway support effect and the relevant relationship between the bolt pre-tightening torque and the pre-tension.
分析了锚杆预应力对巷道支护效果的影响，锚杆预紧扭矩与预紧力对应关系。
Theoretic analysis indicates that the impact effect and stress waves of tap on the workpiece result in extended micro cracks, leading to lower plastic deformation and a much lower tapping torque.
冲击攻丝作为一种新型的内螺纹加工技术，在解决小直径薄板内螺纹加工方面发挥着重要的作用，并具有良好的应用前景。
Theoretic analysis indicates that the impact effect and stress waves of tap on the workpiece result in extended micro cracks, leading to lower plastic deformation and a much lower tapping torque.
冲击攻丝作为一种新型的内螺纹加工技术，在解决小直径薄板内螺纹加工方面发挥着重要的作用，并具有良好的应用前景。
应用推荐