This paper presents a new method to measure tooth error of small module gears.
进行测量，提出了一种在视觉三坐标测量机上测量小模数齿轮齿形误差的新方法。
High frequency noise of gears is mainly from tooth error and base pitch, and low frequency noise from accumulated errors of tooth spacing.
齿轮高频噪声产生的主要原因是齿形误差和基节偏差；低频噪声产生的主要原因是齿距积累误差。
Of all the gear frequency errors, the non-linear dynamic characteristics of gear tooth error, pressure angle error and sprial fluctuation error are compared with the results of the linear system.
在齿频误差中，分析了齿形误差、压力角误差和螺旋线波度误差激振下，转子系统的非线性振动特性，并与按线性模型计算的结果进行了对比。
Taking the straight-line-rack as the tool the error of straight generatrix is measured and by error analysis the tooth profile error and tooth orientation error can be obtained.
以刃边齿条为工具，测量廓面的直母线族误差，通过误差处理与分析获得齿廓总偏差和螺旋线总偏差。
The error correction model of tooth surface was established by machine tool adjustment parameters and meshing principle.
结合机床调整参数、齿轮啮合原理，建立了螺旋锥齿轮齿面误差修正模型。
The machining error affecting the load distribution are errors of the tooth flank direction and the contact line.
影响负荷分布性的加工误差主要因素是齿向误差和接触线误差。
Experiment shows that measurements on geometrical size and evaluation on roundness error of the tooth shape chain board by this measurement method are feasible.
实验表明，用该方法对齿形链链板的几何尺寸测量和圆度误差评定是可行的。
At the basis of distribution law of error formed by the processed pulley with various teeth and its effect on transmission, the scope of tooth of pulley processed is defined.
在研究滚刀加工不同齿数带轮所形成的误差分布规律及误差对带与轮啮合传动影响的基础上，确定了滚刀可加工的齿数范围与参数。
Conclusions the reason of tooth entered soft tissues is judgment error and improper use of the instruments during the surgery.
结论术中判断误差和器械使用不当，是牙体进入软组织间隙的主要原因。
Based on basic theory of maximum error minimum method, double arc parameters for normal tooth outline in rectangle spline hob are optimized to obtain tooth outline in workpiece with minimum error.
根据最大误差最小法的基本原埋，对矩形花键滚刀法向齿形的双圆弧参数进行了优化，使滚刀加工出的工件齿形误差最小。
Meantime, an algorithm to the error compensation of the tooth clearance is implemented.
同时，阐述了实现齿隙误差补偿的软件方法，并采用软件方法加以实现。
The effects of geometric eccentric and deformation of gear blank to motion errors is analyzed and an error model for gear's left and right tooth profiles is built.
分析了齿坯几何偏心和变形对齿轮运动误差的影响；建立了左右齿廓形误差模型。
Tooth deviation of the grinding machine both before and after the error compensation are measured by using CMM gear measuring device.
采用CMM齿轮检测仪测量磨齿机误差补偿前后所加工齿轮齿面误差。
A new calculating method of axial tooth Angle is put forward, which leads to forming error distribution of hob tooth forms.
提出新的轴向齿形角计算方法，使滚刀刀齿形误差分布较为合理。
Through theoretical derivation and experimental verification, a new method is obtained for further reducing tooth curve error of oblique gear and for choosing feed gear wheel.
在应用无差动法滚切斜齿圆柱齿轮的基础上，通过理论推导和实验验证，得出进一步减少斜齿轮齿向误差的可行的挂轮选配新方法。
There are some characteristics about it, for example, highly tracking accuracy and tracking function etc. These characteristics need the require which can accurately measure tooth trace error.
此技术具有跟踪精度高，跟踪性能好等特点，满足了高精度测量齿向误差的要求。
Calculates the tooth profile Angle of pinion cutters with the corrected formula of tooth profile Angle. However, under this condition, the tooth profile designing error is not smallest.
插齿刀的齿形角一般按齿形角修正公式来求，但此时的齿形设计误差不是最小。
The mathematical model to evaluate the tooth profile error of the sector by using the minimum least square method and the minimum zone method is given.
给出了齿扇齿形误差的最小二乘评定与最小区域评定的数学模型；
The radial runout of tooth ring of the coniflex gear, which is an important test item, is an important factor influencing the accumulated error of tooth spacing and the error of tooth spacing.
直齿锥齿轮的齿圈径向跳动是重要的检验项目，是影响齿距累积误差和齿距误差的重要因素。
In the process of the teeth, hob manufacturing error of gear tooth shape of the main impact error and the festival deviation.
在切齿过程中﹐滚刀的制造误差主要影响齿轮的齿形误差和基节偏差。
The above research finds out the influence of grinder error and machining setting parameter error on tooth surface error of spiral bevel gear.
上述研究查明了磨床误差及加工调整参数误差对螺旋锥齿轮齿面误差的影响机制。
The method has higher precision of getting measuring points, less fitting error of tooth form, less artificial interpose in the measuring process and higher measuring precision.
该测量方法具有测量采集点精度高、齿形轮廓曲线拟合误差小、测量过程与误差处理过程人工干预少、测量精度高等特点。
The error correction model of tooth surface and solving method using TSVD were verified experimentally, and the tooth surface machining quality of spiral bevel gear was improved.
实验验证了本文齿面误差修正模型及提出的TSVD法求解的正确性，提高螺旋锥齿轮齿面加工质量。
A valid verifying method of error of indication is introduced for subdivide multi-tooth table in this paper. The evaluation of uncertainty of measurement is given.
介绍了一种对多齿细分分度台综合示值误差进行检定的简便方法，并进行了测量不确定度评定。
The effects of geometric eccentric and deformation of gear blank to motion errors is analyzed and an error model for gears left and right tooth profiles is built.
讨论了齿轮运动误差与模拟齿轮加工过程的关系；分析了齿坯几何偏心和变形对齿轮运动误差的影响；建立了左右齿廓形误差模型。
The relationship between the dividing error of the divider and the machining error of the serrated tooth discs has been found by experiments.
对于分度台的工作分度误差与齿盘加工误差之间的关系进行了实验验证。
Adopting the engaging process of the measuring rack - probe, the error of straight generatrix is measured, and by error analysis, the tooth profile error and tooth orientation error can be obtained.
采用刃边齿条测头，测量齿轮廓面的直母线偏差，通过误差分析分离出齿廓总偏差和螺旋线总偏差。
The tooth profile error and longitudinal form error are calculated, and the change rule with setting Angle of them is got.
本文在推导出齿形误差计算公式的基础上，给出一种使齿形设计误差最小的最佳齿形角的求法。
The error sensitivity of contact position of point-contact tooth surfaces with respect to the mounting errors is an important index to evaluate the gearing performance.
点接触齿面的接触点位置对安装误差的敏感性是衡量齿面传动性能的一个重要指标。
The error sensitivity of contact position of point-contact tooth surfaces with respect to the mounting errors is an important index to evaluate the gearing performance.
点接触齿面的接触点位置对安装误差的敏感性是衡量齿面传动性能的一个重要指标。
应用推荐