Tolerance optimization seeks to minimize the cost with constraints of product requirements and manufacturing ability.
产品公差的优化应在满足使用要求及加工能力允许的条件下以成本最小为目标。
The objective function of process tolerance optimization is established with the fuzzy mathematics based on maximum process capability.
以最大工序能力作为工序公差优化的目标，利用模糊数学的概念建立目标函数。
In order to optimize tolerance values for an assembly system, a model for geometric dimension tolerance optimization was established and an algorithm for optimal tolerance design was proposed.
为优化装配系统中公差链的公差值，建立了几何尺寸公差的优化模型，并提出公差的分层优化设计算法：第一层，解决设计公称值居中的优化问题；
It is designed to improve server selection, load optimization, and fault tolerance.
它专门设计用于改善服务器选择、负载优化和容错。
The assembly tolerance analysis and optimization method based on digital product design model is put forward according to the analysis of digitalization preassembly method.
通过对数字化预装配方法的分析，提出了基于数字化产品设计模型的装配公差分析和优化方法。
Analyzing the characteristics of Taguchi method and tolerance model of robust design, we advance a new strategy of robust optimization design process based on Taguchi method and tolerance model.
分析了田口方法和容差模型法的各自特点，提出了一种综合运用两种方法使其互补的稳健优化设计进程策略。
Screw parameters in VGCN specified by tolerances in TN are expressed as inequation, which is inequation constraint in optimization of tolerance values.
研究了公差网络中的各公差对相应的旋量参数的约束不等式表示，从而构成了公差大小优化的不等式约束。
A method of tolerance analysis and optimization design is investigated. The main key techniques of tolerance analysis and design of the servo mechanism of the guidance head is analyzed.
研究了公差分析与优化设计的方法，分析了导引头伺服机构公差分析与设计的主要关键技术。
The general expressions of kinematic model of 3-dimensional VGCN are presented, which is the equation constraint in optimization of tolerance values.
建立了三维变动几何约束网络的运动学模型的一般表示式，从而构成了公差大小优化的等式约束。
An optimization model of optical tolerance is proposed to enable straight forward calculation instead of the usual tolerance-budget balancing by trial and error.
本文提出的光学公差优化模型可迅速地计算出结果，而不必象通常那样进行反复调整试算。
Optimization method of sequential tolerance design is proposed for 3 dimensional part manufacturing.
提出三维动态公差设计的一般模型和优化方法。
To improve product quality and reduce manufacturing cost, an optimization approach for multi-process dimension and its tolerance was put forward.
为提高产品制造质量、降低产品制造成本，提出了一种多工序尺寸及公差的优化方法。
This paper presents a computer-aided method of automatic generation of dimension chains and penalty function-based tolerance genetic optimization, and the corresponding software has been developed.
研究了一种计算机辅助的交互式尺寸链自动生成方法和基于惩罚函数法的公差遗传优化算法，编制了相应的软件。
This paper presents a computer-aided method of automatic generation of dimension chains and penalty function-based tolerance genetic optimization, and the corresponding software has been developed.
研究了一种计算机辅助的交互式尺寸链自动生成方法和基于惩罚函数法的公差遗传优化算法，编制了相应的软件。
应用推荐