The edge milling process is widely used for manufacture of SSAW pipes. However, in case that proper control is not ensured, defects like welding misalignment or non-through-welding may be caused.
铣边工艺被广泛用于螺旋缝埋弧焊管生产，但控制不好会导致焊管出现焊偏、未焊透等缺陷。
Lasers similar to those used for welding in car factories would be fired through telescopes to 'nudge' piles of rubbish left in orbit.
发射激光的原理就好像是工厂中汽车焊接一样，通过地面的望远镜发射激光，将地球附近的垃圾碎片推离开轨道。
The EAA have several good books about welding that can guide u through this process.
EAA关于焊接那的一些好书已经能透过这一个方法引导你。
Through theoretical and experimental analyses, it is well known that active infrared technology can be applied in the investigation of industrial welding seams.
通过理论和实际的分析，得出主动红外技术能很好地应用于工业焊缝的检测。
Welding the center sills of railway wagons with welding robot is unprecedented through the investigation.
通过调查了解，采用机器人焊接铁路货车中梁还是前所未有的。
Either of two rods through which current flows to form an arc, as in lighting or welding.
碳精棒两根棒的任一根，电流流经该棒形成电弧，如在闪电或焊接时。
The circuit board is placed in the welding stage, the pins through hole components welding, choose appropriate spray tin, soldering start.
将电路板放置在焊台上，针对需要焊接的通孔元件管腿，选择合适的喷锡口，启动波峰焊接。
Through material choice and welding method selection, by working equipment design and manufacture process design, this article explains the method to actualize automobile sensor sealed.
讲述了通过对材料、焊接方法的选择和焊口及工装设计与制造过程设计，来实现汽车传感器封装的方法。
Using the method of jet welding dismantling these through-hole components to avoid these problems.
采用喷流焊的方法拆除这些通孔元件可以避免这些问题。
Through combination adjustment of the thick and thin switches, to make the output welding current be possible to adjust the scope thinner and wider.
通过厚薄两种开关的综合调整，使输出焊接电流去适应更薄和更广的范围成为可能。
Through hole components welding using traditional manual welding or soldering. The circuit board surface mount components and through-hole components mixed together.
传统的通孔元件的焊接采用波峰焊或手工焊接。目前电路板上表面贴装元件和通孔元件混合在一起。
Through changing the sealing structure to sleeve type and optimizing the welding technology, the security and reliability of the boiler equipment are improved.
通过将密封结构改进为套筒式和优化焊接工艺，提高了锅炉的安全可靠性。
Because of the complexity of welding process, the research of weld process produce hot and stress through method of experiment is very difficulty.
因为焊接过程的复杂性，所以很难通过实验的方法对焊接过程产热和应力分布进行研究。
A new view of characteristic zone of fusion welding joint is put forward through observations and researches of many fusion welding joints.
通过大量的熔化焊接头试样的观察和研究，提出了熔化焊接头特征区域划分新方案。
The characteristics of compound plate are understood through welding of the compound plate, thus the welding efficiency and quality can be improved.
通过对不锈钢复合板的焊接，从中了解和掌握复合板的特性，提高了焊接效率和焊接质量。
The welding wire exits through the second drive assembly.
焊丝从第二个驱动组件穿出去。
Through the acquisition of welding currents and voltages during welding, the arc behavior of welding process was analyzed.
对焊接过程的电流及电压波形进行采集，分析焊接过程的电弧行为。
The tested results show that the steel has good welding adaptability through analyzing the mechanical properties and metallurgical structures of the welded joints.
通过对焊接接头的力学性能和金相组织分析比较，证明该钢具有良好的焊接适应性。
Through analysis on inside weld forming and welding procedure of SSAW pipe, it pointed out weld crack is easy to appear in brittle temperature zone in welding pool.
通过对螺旋埋弧焊管内焊缝成型和焊接过程的分析，指出焊缝裂纹易产生在焊接熔池脆性温度区。
Through experiments in welding, the paper has proved its excellent properties from the effects of welding technology, mechanical strength to electric conductivity etc.
本文通过焊接试验研究，从焊接工艺效果、机械强度、导电性能等方面证明了这种新型钎焊料的优异特性。
It can be predicted that the cylindrical shell structure is better than the plane structure in reducing welding residual stress through local loading.
因此可以预见，对于应用局部加载降低结构体焊接残余应力，柱壳结构要比平板结构效果更好。
The welding object is electrically connected with the substrate through the welding blocks.
该焊接对象通过该焊块与该基板进行电性连接。
Tube bundle fix the drooped structures through welding for both ends of upper header and make fly ash drop by rapping the end plate of lower header.
锅炉中的管束是上部集箱的两端通过焊接固定垂下的结构，通过锤打下部集箱的端板，振落飞灰。
We find that the pore number will be reduced through depressing metallic vapour if welding speed is increased with constant laser power.
结果表明，在一定的激光功率下，提高焊接速度可减少金属蒸气的形成，从而降低气孔数；
The experimental research on explosion welding through symmetric collision was conducted and new app-(lications) proposed.
介绍了对称碰撞爆炸焊接的实验方法，总结了它的实际应用。
The whole process of the relief of the welding residual stress through an explosive treatment is simulated by using the nonlinear dynamic finite element method.
利用非线性动力有限元法对爆炸处理消除焊接接头残余应力的全过程进行了数值模拟。
Through hole components welding using traditional manual welding or soldering.
传统的通孔元件的焊接采用波峰焊或手工焊接。
Through hole components welding using traditional manual welding or soldering.
传统的通孔元件的焊接采用波峰焊或手工焊接。
应用推荐