Install IAC motor to throttle body.
安装IAC马达至节气阀体。
Throttle Body Assemblies described here use an aluminum casting.
这里描述的节气门体组件使用的铝铸件。
Smooth operation of throttle linkage and throttle body air valve.
节流连杆和节流体空气阀的平稳操作。
The mass of the Throttle body assembly is defined on the outline drawing.
风门装配的质量已在轮廓图中标出。
A component, such as an intake manifold or a throttle body, has an air passage.
一种部件，例如进气歧管或节气门本体，具有空气通道。
The Throttle body contains bearings for mounting the Throttle Shaft across the bore.
节气门体包含横跨镗孔、用于安装节气门轴的轴承。
The Throttle body has a by pass hole and IACV for meeting the idle airflow requirement of the engine.
节气门体有一个节流孔和IACV，以满足发动机怠速气流要求。
Throttle body made from high temperature and high pressure liquid into the evaporator of refrigeration.
节流机构使制冷从高温高压液体进入蒸发器。
This cell was manufactured to build and full function test a throttle body for the automotive industry.
该元件制造用于为自动化工业建造和全功能测试，为汽车行业节气门。
The dimensions of the Throttle body assembly are defined on the Throttle body assembly outline drawing.
风门装配的尺寸如风门装配轮廓图所示。
The Throttle body Assembly is designed to withstand the following functional and environmental durability tests.
风门装配的设计可承受如下功能，环境耐久试验。
The Throttle body assembly shall meet all performance requirements listed herein at the normal operating conditions.
在正常操作条件下，节气门体总成必须满足本文所列的所有性能要求。
The Throttle body provides surfaces for mounting between the Motorcycle's air intake duct and the engine intake manifold.
风门表面留有安装摩托车进气管和发动机进气歧管的位置。
The test results indicate that the throttle body assembly can meet the durability and reliability requirements of motorcycle.
试验结果表明节气门总成能够满足摩托车对耐久性和可靠性要求；
Throttle body. The throttle body is the part of the air intake system that controls the amount of air flowing into an engine's combustion chamber.
节气门体，同时就节气门体的进气系统的一部分，控制适当的气流流动到发动机的燃烧室。
An air duct will mount to the Throttle body assembly air intake snout. The snout lip dimensions are defined on the Throttle body assembly outline drawing.
气管加装在风门装配进气口上。进气口尺寸如风门装配轮廓图所示。
The Throttle body assembly will mount to the manifold snout and intake manifold interface dimensions are defined on the Throttle body assembly outline drawing.
节气门体总成安装在歧管口，进气歧管接口尺寸如节气门体总成轮廓图所示。
High pressure fluid through the filter, the gush after the throttle body into the evaporator, and in the corresponding under low pressure, the quantity of heat of evaporation from around.
高压液体经过过滤器、节流机构后喷入蒸发器，并在相应的低压下蒸发，吸取周围的热量。
Disconnect the accelerator cable, the cruise control cable (if equipped), and the transmission line pressure cable (if equipped) from the throttle body and remove them from the cable bracket.
从节流阀体上拆下加速器电缆、车速控制电缆(若已装备)、及变速箱管线压力电缆(若已装备)，并将它们从电缆托架上拆除。
The body of valve for Electronic Throttle Control(ETC) is an example among them.
汽车电子节气门控制（ETC）的阀体就是其中一例。
The body of valve for Electronic Throttle Control(ETC) is an example among them.
汽车电子节气门控制（ETC）的阀体就是其中一例。
应用推荐