This paper introduces the design and implementation of parison wall thickness control system in blow molding machine.
介绍了型坯壁厚控制系统在中空吹塑机中的设计与实现。
Second, the thickness control system of cold rolling mills driven by two hydraulic cylinders is taken as the research object.
冷轧机轧制的带材较薄，对同步控制精度的要求更高。
In the research of the membrane thickness control system of IBS plating machine, as having adopted modern detection means, measure precision improves greatly.
在离子束溅射镀膜机的膜厚控制系统的研究中，由于采用了现代检测手段，使测量精度大大提高。
The parameter reflecting mechanical properties of rolling stock is value Q which determines directly both parameter setting for thickness control system and control effect.
是反映轧制过程中轧件力学性能的参数，直接决定厚度控制系统参数设定和控制效果。
Discusses the nonelinearity and coupling of the plastics thickness control system, and adopts NN serial decoupling algorithm to solve the difficulty in multivariable nonlinear coupling.
讨论了薄膜厚度控制的非线性和耦合性，应用神经网络串行解耦算法，解决多变量非线性耦合问题，同时还采用了改进的学习算法———动量法，并与传统算法做了仿真比较。
The control system will be intelligent by introducing artificial intelligence technique into AGC strip steel thickness control system to increase control accuracy of strip steel thickness.
将人工智能技术引入到AGC带钢厚度控制系统中可使控制系统具有智能化，提高带钢厚度的控制精度。
Precisely forecast strip thickness at the exit of cold tandem mill's each stand has very important significance for perfect automatic gauge control system and improve quality of product.
准确预测冷轧机各机架出口带钢厚度对于完善自动厚度控制系统和提高产品质量具有重要意义。
Average wafer thickness value on basis of 100% control with an automatic inspection system.
晶片的平均厚度值以100%控制的自动检测系统的测量值为基础。
This control system developed by the core of single chip computer can anti-divide the thickness of the gland shim, It has good dividing precision and high sorting efficiency.
以单片机为核心开发的该控制系统能对缸盖垫片的厚度进行自动分选，从而保证了缸盖垫片的分选精度，提高了分选效率。
This paper analyzes the reasons leading to uneven thickness of cold rolled strip steel, problems existing in AGC control system and component and application prospect of intelligent technique.
分析了冷轧带钢厚度不均产生的原因、A GC控制系统存在的问题及智能技术的构成和应用前景。
New closed loop observer and control system was added on rolling machine for the measurement of sheet film thickness, thus made the rolling machine become a truly mechatronic product.
在新研制的压延机上增加塑料薄膜厚度闭环测控系统，使压延机成为一套真正的机电一体化设备。
This paper introduces anti-jamming project for thickness-stacked stamping control system of motor iron-core with skewed slot from hardware and software.
本文从硬件和软件两方面介绍了电机铁心扭槽叠扣冲压控制系统的抗干扰设计。
It introduces the hardware and software design of control system in X-ray thickness gauge used in cold-rolled steel strip.
介绍了一种X射线冷轧测厚仪控制系统的硬件设计和软件设计。
Automatic gauge control system in double-stand reversing cold mill is introduced. This system is consists of regulating device, thickness gauge and tachometer.
介绍了双机架可逆式冷轧机组厚度自动控制系统，该系统由调节装置、测厚仪和测速仪组成。
Coupling control equation of system was presented based on assumption method and change tendencies of critical velocity for flutter with both gap and the thickness of beam were discussed.
采用假设模态法建立耦合控制方程。分析系统的颤振临界流速随间隙和板厚的变化规律。
Wall-thickness accuracy of steel tubes rolled on a pilger mill can be improved with the automatic process control system established.
建立工艺过程自动控制系统提高周期轧管机轧制的钢管壁厚精度。
The calculations of radiator surface area and heat insulation layer thickness are necessary for the design of passive thermal control system.
纳卫星的被动热控系统对卫星舱内的温度控制及其有效载荷的可靠工作具有重要意义。
In the soft reduction control process, the slab thickness and drafts can be controlled by the hydraulic system through controlling the inlet and outlet gaps of each segment.
在扇形段轻压下控制中，通过对每个扇形段的入口侧和出口侧的两端辊子的辊缝进行控制，实现对板坯厚度及压下程度的控制，其控制是由液压系统来完成的。
Tin thickness closed-loop control for tinning line, a kind of typical non-linear complex system with large time delay, is discussed.
武钢冷轧厂电镀锡线锡层厚度无模型自适应（FMA）控制系统是专门为了解决大滞后时变的非线性复杂系统控制难题而研制设计的。
Through import the thickness and the control precision of the workpiece. system can get the most excellent combination of technics parameters.
通过输入工件的加工厚度和加工控制精度，自动得出最优的工艺参数组合。
The working principle, characteristics and main control parameters of film extruder production line PET film production objective thickness self-control system were introduced.
介绍了拉幅生产线聚酯薄膜生产目标厚度自动调整系统的工作原理、工作特点、主要控制参数。
With the hydraulic control system its cutting speed can be adjusted easily by the size and the thickness of the caliber.
它采用液压进给，进给量切削速度可根据口径大小、臂厚随意调整。
With the hydraulic control system its cutting speed can be adjusted randomly by the size and the thickness of the caliber.
它采用液压进给，进给量切削速度可根据口径大小、臂厚随意调整。
With the hydraulic control system its cutting speed can be adjusted randomly by the size and the thickness of the caliber.
它采用液压进给，进给量切削速度可根据口径大小、臂厚随意调整。
应用推荐