This case uses thermal loads for XL associated with RVOS condition.
这种情况下使用的热负荷加大相关RVOS条件。
This method can be used to generate the thermal loads for finite element analysis.
该方法可作为使用有限元法分析桥梁温度应力的边界条件。
They are designed to absorb and dissipate the thermal loads associated with the most severe braking and tensioning applications.
它们的设计是为了吸收和消散的热负荷相关的最激烈的制动和张应用。
For test specimens built up symmetrically from 16 layers of fiber reinforced material the stress distributions are calculated under axial and thermal loads.
本文对用16层纤维增强材料对称铺设成的试样，在轴向载荷和热载下的应力分布作了计算。
The results of actual prediction show that this prediction model based on the synthesized BP network performs very well in the prediction of cogeneration plant thermal loads.
实际预测结果表明，基于合成BP网络的预测模型能很好地实现对热电厂热负荷的预测。
During the working process, it bears thermal and mechanical loads simultaneously, because of which it tends to crack and even break.
它在工作过程中，受到热负荷和机械负荷的共同作用，工况恶劣，容易产生裂纹而导致破坏。
In addition to controlling mechanical shaft and bearing loads, the coupling further protects the encoder by providing a high degree of electrical and thermal isolation between coupled shafts.
除了控制的机械轴和轴承载荷，耦合进一步保护通过提供电力和热轴之间的耦合隔离高度编码器。
These withstand heavy loads and thermal stresses well.
它们能很好地耐受重负荷和热应力。
This requires design concepts that provide thermal growth flexibility while reacting large torques, separating loads and external ducting loads.
这就要求设计概念，提供热增长的灵活性，同时反应，大扭矩，分离负荷和外部管道负荷。
Operation: Once get power supply, loads and thermal resistors connected, press the power switch of temperature controller, and then it will start temperature control program automatically.
使用：接好电源、负载及热电阻线后，按下温控器电源开关，温控器即可自动投入定温控制运行。
The buckling of large vertical cylindrical shells with welds subjected to local thermal action and axial loads was studied with numerical method by using ANSYS code.
对大型直立设备安装过程中的现场焊接热处理过程中在轴向载荷和局部热载荷共同作用下的屈曲问题进行数值研究。
The concern of pump is the increased thermal cycling and vibratory loads.
泵的关注增加的热循环和振动载荷。
The practical thermal efficiency for different resistance loads is measured by using thermal efficiency apparatus. The method to determine the load for the optimum thermal efficiency is introduced.
利用热效率实验仪测量了不同负载电阻的热机实际效率，并确定了最佳热效率负载电阻的测量方法。
Thermal load is one of the main loads of arch dam, at present, the method of adopting thermal load of normal concrete in RCC arch dam calculation underestimates the action of temperature.
温度荷载是拱坝最主要的荷载之一，目前，通常采用计算常态混凝土温度荷载的方法计算RCC拱坝，这低估了温降的作用。
The finite element method for the strength problem of C/M FGM underthe thermal shock loads is established.
讨论了梯度材料在热冲击下强度问题的有限元解法。
While at high loads, there exists a region of methanol concentrations for getting optimum thermal efficiency.
对于较高负荷，存在一个指示热效率较高的甲醇浓度区间。
Since many transformers do not carry continuous loads, advantage can be gained from the thermal time lag to carry higher peak loads without exceeding the temperature limits.
由于许多变压器并不带持续负荷，这就可利用发热时间的滞后来带上更高的峰值负荷而不至于超出温升的限定值。
Chemical and petrochemical plants have long displayed a preference for ductile iron because of its ability to withstand shock loads, either thermal or physical.
由于球墨铸铁具有良好的耐冲撞装卸性能，及热学和物理性能，所以长期以来，化工厂和石化企业就特别爱好使用球墨铸铁。
However, the brake thermal efficiency increases and the CO emissions almost equal at high loads.
高负荷时发动机有效热效率增加而CO排放基本相当。
Next, on the basis of the transient-state thermal analysis, the thermal elastic-plastic analysis of the thermal-structure couple is obtained in the axial symmetry loads.
其次，在喷管轴对称模型瞬态热分析的基础上研究了轴对称载荷下热—结构耦合场的应力分析。
An improved PCA arithmetic model is applicable to nonlinear plant thermal processes using local PCA model for various power loads based on the historical data.
为了使基于PCA的传感器故障检测和重构方法适用于非线性较严重的热工过程，对该方法进行了有效的改进。
The thermal efficiency is higher than that of diesel operation at high loads, but lower at low loads.
在高负荷时，发动机燃用纯甲醇的热效率高于原柴油机，而且可以切断电热塞电源，发动机仍能稳定运转；
The thermal efficiency is higher than that of diesel operation at high loads, but lower at low loads.
在高负荷时，发动机燃用纯甲醇的热效率高于原柴油机，而且可以切断电热塞电源，发动机仍能稳定运转；
应用推荐