This paper discusses the theory of deformation monitoring with two GPS satellites.
论述了用两颗GPS卫星进行变形监测的原理。
Raverse analysis, based on the plasticity theory of deformation and FEM, however, can calculate the blank contour directly from a given part.
反向模拟结合了塑性形变理论和有限元技术，直接由工件反算出毛坯。
It is easy to obtained definite problems of finite deformation beams under various simple cases and its linear theory.
应用本文方法可以很容易地得到梁有限变形各种简单情形的定解问题以及它的线性理论。
The paper has studied straightening stress and residual deformation of circular shaft by using elastic - plastic theory, deueloped calculation formula of straightening loud in given deflection error.
从弹塑性理论出发以圆截面轴为例对校正应力与残余变形进行了分析研究，提出了在给定弯曲误差下的校正载荷的计算公式。
The theory of statistical dislocation link length distribution is an active field in the modern microscopic quantitative theory of metal plastic deformation.
变形金属位错链长度统计分布理论是现代金属塑性变形定量微观理论最活跃课题之一。
The deformation and stress condition of the micro-composite are studied according to the shear-lag theory and strain-hardening law.
按照剪切滞后理论和应变硬化规律，研究微复合材料的变形和应力状态。
From the plastic flow theory, the three-dimensional deformations and stresses of the deformation zone are formulated.
根据塑性力学流动理论，分析推导了变形区三维变形和应力的数学模型。
Several problems of theory about elastic rolls deformation were studied in this paper.
本文对轧辊弹性变形理论的几个重要问题进行了研究。
The results show that the solution of differential equations' MWR is successful, and the precision of the shear deformation theory of cylindrical shells is satisfactory.
结果表明：本文提出的控制微分方程的加权残值法解是成功的；而且圆柱壳的剪变形理论有满意的精度。
By the variational method, the governing equation of the plate non-linear theory is solved, and he relationship between load and deformation of a single spring leaf is obtained.
应用薄板非线性理论的变分方法求解基本方程，得到了单片碟形弹簧的载荷和变形关系以及应力分布及其计算公式。
Based on genetic programming (GP) theory, the mathematical modeling method of dam deformation monitoring is researched.
研究了基于遗传规划(gp)理论的大坝变形监测数学模型的建模方法。
This paper analyzes the influence of sliding friction on contact deformation in theory and demonstrates it by means of test.
从理论上分析了滑动摩擦对接触变形的影响，给出了压陷量的修正公式，并通过试验加以验证。
Using the theory of design on plate deformation, with attainment of high yield, we can find mathematics model and method on slab calculation.
利用中板变形规程的设计原理，以提高成材率为目标，得到了坯料计算的数学模型及基本方法。
Based on the theory of multi-phase media continuum mechanics, the coupling instability theory of coal-methane outburst is proposed under finite deformation.
本文在多相介质力学的理论基础上，提出了煤体有限变形下煤与瓦斯突出的耦合失稳理论。
It bases on the classical plastic theory, and the components of wetting deformation under complicated stress state may be determined clearly.
该模型依据经典塑性理论，能够明确指定复杂应力状态下湿化变形的各分量。
This paper applies the theory of limited deformation analysis to the non-linear problem of the geometrician and creeping material for the frozen-wall.
本文用有限变形理论对人工冻结壁施工的几何非线性和冻土蠕变材料非线性问题进行了非线性数值分析。
The constitutive equation in the present method is based on flow theory of plasticity to consider the loading history, while deformation theory of plasticity in the classical inverse analysis method.
改进的反向模拟法采用了一种基于塑性流动理论的本构方程，可以充分考虑应变历史对塑性变形的影响。
Using the theory of stochastic dielectric, the laws of deformation in space of different Angle in coal layers have been deduced.
利用随机介质理论，建立了不同倾角煤层的采空区所对应的地表空间变形规律。
The theory and method of finite element analysis of sheet metal forming based on deformation theory was explored, and the computer program was implemented.
研究了基于形变理论的金属板料成形有限元分析的理论和方法，并实现了计算程序。
Using the Simple High order Shear Deformation Laminate Theory and large deformation theory, the geometric nonlinear analysis of rubber rectangular composite laminate plate is presented.
文中应用简单高阶剪切层合理论和大变形理论对各向异性纤维增强的矩形橡胶复合材料层合板进行了几何非线性分析。
Based on the deformation theory of linear hardening materials, a simplified finite element analysis method is proposed to calculate the limit load of structures.
基于线性硬化材料形变理论，本文提出了一种计算结构极限载荷的有限元简化算法。
Also involved are the deformation theory, design, machining and operational performance of the waved groove.
介绍了波形孔型的变形原理、设计与加工以及应用情况。
A new molecular theory of elasticity for TPUE at large deformation was presented.
从而提出了热塑性型聚氨酯弹性体的大形变弹性分子理论。
Abstract: : Based on the author's many years of practical experience in deformation observation and theory methods of engineering measurement is discussed in this paper simple analysis.
摘要：文章根据作者多年实践经验对工程测量的理论策略及变形观测进行了简单的分析阐述。
In this paper, under the guidance of theory of error, the reliability of deformation observation network is studied.
本文从误差理论出发，讨论了变形监测控制网的可靠性。
The joint deformation of DC upset butt welding was studied by using theory of plastic deformation and rigid-viscosity plastic material model.
采用塑性变形理论和刚粘塑性材料模型研究了直流电阻对焊接头的塑性变形。
In shape theory, the three-dimensional deformation theory of plate and strip rolling is an important and difficult study content.
板带轧制的三维变形理论是板形理论研究的重点和难点。
In shape theory, the three-dimensional deformation theory of plate and strip rolling is an important and difficult study content.
板带轧制的三维变形理论是板形理论研究的重点和难点。
应用推荐