Free emitter resources — close the emitter.
释放发射器资源——关闭发射器。
Send the event -- send the event using the emitter.
发送事件——使用发射器来发送事件。
Free the emitter resources — close the emitter.
释放发射器资源——关闭发射器。
Pilot beam: for precise positioning of the emitter.
导向射束：可精确定位发射器。
The Emitter can define the communication style on its own.
发送者可以单独定义通信方式。
We have the geometry, now it's time to create the emitter.
我们有了几何体，现在要创建发射器。
It just tells the WPS Cluster the name of the emitter factory.
只是将发射器工厂的名称告知WPS集群而已。
The region in a transistor between the emitter and the collector.
晶体管中发射极和集电极之间的区域。
Most of the energy not picked up by a receiver can be reabsorbed by the emitter.
发射器可将绝大多数未被接收器接收的能量重新吸收回去。
The base region is always very much narrower than the emitter or collector regions .
基极总是比发射极和集电极薄得多。
The emitter will attempt to pass the event to the event server via a direct EJB invocation.
发射器将试图通过直接的ejb调用传送事件到事件服务器。
The null must intersect with the emitter at the point where you want to emit particles.
这个空物体必须和发射器有交叉的点以便于从这些部位发射粒子。
One of the commonly used methods to reduce this fall-off is by increasing the emitter area.
另一个是如何提高发射极发射电流的有效面积。
Figure 4 illustrates the configuration resources that can be used by the emitter factory profile.
图4示例了发射器工厂概要使用的配置源。
In contrast, if the emitter ledge is too thin, it may not effectively passivate the surface.
相对的，假如射极突出部太薄，将无法有效抑制表面复合电流。
The emitter factory profile settings described above are demonstrated in the following two sections.
上面描述的两种发射器工厂概要设置将在下面的两个章节中进行介绍。
With the protection of photoresist sidewall, the emitter passivation ledge is fabricated by wet etch.
利用光刻胶形成保护侧墙，用湿法腐蚀来形成发射极钝化边沿。
Once this occurs, the emitter validates the event by calling the validate() method on the event instance.
一旦开始验证，发射器通过调用事件实例上的 validate()方法验证事件。
Then RT technology is used to fabricate emitter and rapid spray tooling for trial-produce of the emitter.
应用快速模具技术制备滴管快速喷涂模具，进行产品试制；
The density of holes in the base is less than the density of free electrons in the emitter and collector .
基极中空穴的密度小于发射极和集电极中自由电子的密度。
The result showed that the region under the emitter was more badly shunted than the other emitter regions.
结果表明，电池前电极穿透发射区所引起的漏电电阻率值比其他发射区域的漏电要严重的多。
In the paper, the Galerkin penalty finite element method was applied to simulate the flows in the emitter.
该文采用加罚有限元方法对滴头内流动进行数值模拟，详细分析了“迷宫式”滴头在不同流量时的流动特性。
When the emitter receives a CBE, it will use this filter to determine if the event should be sent to the CEI server.
当发射器接收到CBE 时，它将使用过滤器决定是否把该事件发送到CEI 服务器。
Provided that no failures occur in the above steps, the emitter will then attempt to submit the event to the event server.
假设上述步骤中没有出现故障，发射器将试图提交事件到事件服务器。
Also recommended is to animate the emitter in order to get more lively flames, or use more than one emitter (Final rendering. ).
也推荐动画这个发射器得到更多的真实火焰，或使用超过一个发射器。
To disable event validation, set a new custom property named validateEvent in the emitter profile. Give it a boolean value of false.
要禁用事件验证，在发送器配置文件中设置一个新的自定义属性validateEvent，并将它的值设置为布尔值 false。
The experimental results show that adding rare earth oxide into molybdenum can improve the secondary emission coefficient of the emitter.
实验结果表明，在钼中添加稀土氧化物可以提高发射体的次级发射性能。
The experimental results show that adding rare earth oxide into molybdenum can improve the secondary emission coefficient of the emitter.
实验结果表明，在钼中添加稀土氧化物可以提高发射体的次级发射性能。
应用推荐