Typical Assignment: Test burn rates of new propellants.
典型的任务：测试新的推进剂的燃烧率。
The booster will burn for about 60 seconds, enabling engineers to validate and test its performance.
该助推器将会燃烧大约60秒左右，使的工程师可以对它的性能可以进行证实与测试。
It will burn a mixture of solid propellant (HTPB, or hydroxyl-terminated polybutadiene) and liquid oxidiser (high-test peroxide, HTP) for 20 seconds.
它将点燃固体推进燃料(HTPB，或称羟基封端聚丁二烯)和液体氧化剂(高挥发性过氧化物，HTP)的混合物持续20秒。
When terminal test approaching, all students burn the midnight oil to study.
快要期末考试了，同学们都熬夜学习。
DGUANLONG shall discuss with customer to make sure the power in house Burn-In and life test procedures.
将与客户评估并确认电源产品室内老化寿命测试过程。
The mechanism of profile grinding burn and its influencing factors are analysed through the simulated test of profile grinding racks, and the improvements of grinding burn are proposed simultaneously.
采用金相分析法，分析齿轮烧伤试件的齿面温度分布状态，结合成形磨削齿条的模拟试验，研究成形磨削烧伤形成机理及影响因素，提出了避免成形磨削烧伤的工艺措施。
Method: The teaching of moist burn medicine includes medical knowledge, diagnosis, medical skills, review course and assessment and test.
方法：适用于烧伤湿性医学的教学模式主要有“知识传授课、诊断性补修课、技能训练课、综合复习课和评价测试课”。
Based on the burn-out incident of the mutual inductor due to its internal wet-ting, necessity of the preventative oil test in production is presented.
通过互感器内部受潮烧毁爆炸案例，阐述预防性油试验在生产运行中的必要性。
The pressure-time trace from the KDX-002 static test of the Kappa-DX rocket motor will be used to estimate the propellant burn rate, with the results compared to Strand Burner data .
压力-时间痕量从kdx- 002静力试验的河童的DX火箭发动机将被用来估计推进剂燃烧率，与结果相比， 钢绞线燃烧器的数据 。
When designing a burn-in test system, one task is to determine the best way to switch all the output voltages to be monitored.
在设计老化试验系统时，任务之一就是确定切换所有输出电压的最佳方式。
Analysis and test of speed controller circuit of certain electric bicycle is performed to find out the reason for a frequent burn-out of power FET of the original controller during working.
通过对某种型号电动自行车调速控制器的剖析及试验，找出了原控制器使用过程中频繁烧坏功率场效应管的原因，研制出了一种改进型控制器电路，从根本上解决了原电路存在的问题。
This paper describes the CAD method for MCM-C, the fabrication and metallization processes of MCM-C substrates, and the technologies for die test, burn-in and interconnection.
介绍了MCM-C的CAD设计方法，以及MCM-C基板的制作与金属化、芯片的测试和老化、芯片互连等工艺。
In the light of no integrated surging and burn-in test system at high temperature for slice capacitor, a smart test system based on 89c52 core is developed.
针对目前片式电容器生产厂无大容量高温浪涌与老化试验同时进行的设备现状，设计并实现了以89c52单片机为核心的智能化高温浪涌测试与老化试验系统。
Analysis and test of speed controller circuit of certain electric bicycle is performed to find out the reason for a frequent burn-out of power FET of the original controller during working.
通过对某种调速控制器的剖析及试验，找出了原控制器使用过程中频繁烧坏功率场效应管的原因，斫制出了一种改进型控制器电路，从根本上解决了原电路存在的问题。
The test results show that it is feasible to enhance the combustion efficiency of fluidized bed boilers through the use of the cyclone burn-out chamber.
试验结果表明：采用旋风燃尽室来提高沸腾炉的燃烧效率是可行的。
According to the test data and field data of transmitter and receiver, the method of "maximum mean residual life" is used to determine an optimum burn-in time.
根据发送器和接收器的老化试验数据和现场数据，使用“最大平均剩余寿命”的方法分析确定了一个较优的老化时间。
Conclusion the established sterility test method of the Burn I oil agent is scientific and accurate.
结论采用该法对烧伤一号油剂进行无菌检查，方法可行，结果准确。
In this paper, some anti-burn on additives for green mould sand produced at home were reviewed and several practical test methods were recommended.
笔者对国内若干种湿型砂抗粘砂附加料作出评论，并推荐几种实用的检测方法。
These sockets are used in EPROM programmers, burn-in boards and test jigs.
这些插座在EPROM编程器、老化板和测试夹具中使用。
The specimens may not burn with flaming combustion for more than 10 seconds after either application of the test flame.
在每一次本生灯灯火焰燃烧10秒钟移开后，没有任何一个试片被火焰点燃超过10秒钟。
The capacity, footprint, and power requirements of the environmental and altitude test systems vary from those of the burn-in system.
此系统可看作环境舱来支持老化的低温与湿度测试。容量，占用空间与功率需求与其他系统不同。
The capacity, footprint, and power requirements of the environmental and altitude test systems vary from those of the burn-in system.
此系统可看作环境舱来支持老化的低温与湿度测试。容量，占用空间与功率需求与其他系统不同。
应用推荐