做拉伸试验。
Layered fracture occurs after tensile test of high strength ship plate.
高强船板拉伸试验后出现断口分层现象。
The failure assessment diagrams were derived from the tensile test results.
评定根据母材和全焊缝拉伸试验结果建立评定曲线；
The factors of the tensile test of carbon fibers were discussed in this paper.
本文讨论了碳纤维强伸实验的影响因素。
The single tensile test of low carbon steel is an important content of mechanics tests.
低碳钢的单向拉伸试验是力学试验的一项重要内容。
The fracture surface appeared intergranular crack, due to the oxide formed during tensile test.
拉伸过程中形成的氧化物夹杂成为裂纹源，断口表现为沿晶断裂。
The result of insitu-tensile test shows that the behavior of fracture is transcrystalline rupture.
扫描电镜下的原位准静态拉伸试验表明，合金的断裂行为是穿晶韧性断裂。
It is found that the weld of fine grain steel break apart from heat effect zone in the tensile test.
经实验发现细晶粒碳钢焊接接头拉伸试验断口在远离热影响区的母材上。
This paper discusses the fracture shape of the tensile test sample in practice teaching of mechanics.
本文就力学实践教学中拉伸试样断口形状问题进行探讨。
Before completing linkage screw in the machining, finished products are needed to do the pre-tensile test.
连杆螺钉在加工完成后成品交验前，要求进行预拉伸试验。
The mechanical properties and fracture process observation was studied by in-situ tensile test of 93w-y2o3.
研究93 W - Y 2o 3合金的力学性能，并通过扫描电镜原位拉伸试验观察93W - Y 2o 3合金的断裂过程。
A uniaxial tensile test method for measuring mechanical properties of MEMS thin film materials is presented.
介绍了一种用于MEMS薄膜材料力学特性测试的单轴拉伸试验方法。
The relationship between stress and strain in a particular material is determined by means of a tensile test.
最佳答案之间的关系应力和应变在一个特定的物质决心通过拉伸试验。
Through study on triaxial tensile test of soil from the dike of Yellow River, a lot of beneficial results are achieved.
针对黄河大堤典型土质开展了三轴抗拉试验研究，得出了许多有益成果，并就具体应用方法进行了探讨。
The quasi-superplasticity of leaded brass for bearing cage was investigated through the constant velocity tensile test.
通过恒速拉伸试验，对一种生产保持架用铅黄铜的准超塑性进行研究。
Through the tensile test in SEM, the constraint effects of particles have been investigated qualitatively in microscope.
在SEM下的拉伸试验，直接从微观上证明了这种约束的作用。
To meet the needs of tensile test for small diameter bolt and screw, this article gives a design of tensile testing device.
针对小直径螺栓和螺钉的拉伸试验要求，设计了一种拉伸试验装置。
The model was developed in the framework of micro-mechanics, in combination with the existing corroded coupon tensile test results.
根据预腐蚀件的拉伸实验结果，对模型的正确性进行验证。
According to the processing performance titanium alloy materials, using a CNC machining center processing the tensile test specimen.
根据钛合金材料的加工工艺性能，采用数控加工中心加工出拉伸实验所用试件。
If a tensile test specimen fails to meet the requirements of 7.4.2, two further test specimens shall be obtained for each one that failed.
如果抗拉强度试样不符合7.4.2的要求，对每一个不合格的试样再取两个试样进行试验。
The relationships between damage energies of HTPB propellants and storage ageing time were investigated by uniaxial repeated tensile test.
由单轴反复拉伸试验分别研究了含键合型防老添加剂和防老剂h的HTPB推进剂破坏能与贮存老化时间的关系。
ABS samples of physical aging and strain aging were studied by universal tensile test machine and differential scanning calorimeter (DSC).
用万能拉伸实验机和差示扫描量热仪(DSC)对物理老化和应变老化的ABS试样进行研究。
The backlight photography with single sample was used to measure the true stress-strain of the ductile material after necking in tensile test.
本文采用单试样逆光拍照法对延性材料拉伸试验缩颈后的真实应力-应变进行了有效的测量。
This paper analyzes the uncertainty of tensile test measurement for square specimen and gives formulae to calculate the uncertainty of measurement.
对矩形试样拉伸试验测量的不确定度进行分析，得出了计算其不确定度的公式。
The influences of deformation rate on the mechanical properties of 304 austenitic stainless steel were studied by tensile test at room temperature.
采用室温拉伸实验研究了不同变形速度对304奥氏体不锈钢力学性能的影响规律。
Tensile test shall be carried out on one pipe sample representing each inspection lot. But not less than one pipe sample representing each heat test.
每批检验品只抽一个钢管代表整批的来做张力测试，但是至少有一个以上样品代表整批做热度测试。
The mechanical property of AZ31 magnesium alloy rolling sheet under different temperatures and strain rates was studied through uniaxial tensile test.
通过单向拉伸试验研究了AZ31镁合金轧制板在不同温度和应变速率下的力学性能。
Effects of tin on the microstructure and mechanical properties of ZA62 alloys were investigated using optical microscopy, XRD analysis and tensile test.
采用金相显微镜、X射线衍射仪等分析测试手段，研究了锡对ZA62合金显微组织及力学性能的影响。
The results show that it is a reasonable tensile test method characterized by its convenience, uniform stress distribution, higher stability and lower size effect.
结果表明，该方法简单方便、应力分布均匀、试验结果稳定、尺寸效应较小，是混凝土一种理想的拉伸试验方法。
The change of strain rate and stress rate of samples with and without yielding phenomenon was studied during the tensile test under the control of grip separate rate.
采用夹头分离速率控制方式对有屈服现象和无屈服现象的试样进行拉伸试验，探讨了试验过程中试样应变速率和应力速率的变化情况。
应用推荐