The tensile strength, heat resistance and processability of the system decrease slightly with the increase of superfine wollastonite amount.
随着超细硅灰石用量的增大，体系的拉伸强度、耐热性能和加工性能都稍有下降。
As these properties are reduced there is also a decrease in tensile strength and an increase in the ductility and toughness of the steel.
随着这些性能的降低，拉伸强度也降低而钢的延展性和韧性则会提高。
The machine damage brings the tensile strength and the elongation value of beryllium to decrease.
机加工损伤使铍的抗拉强度和延伸率均有较大降低。
Moreover, it is revealed that the deformation resistance in the thermal cycle process is related to the increase of its tensile stress and the decrease of yield strength.
研究进一步表明，材料变形的难易程度又与变温循环过程，热疲劳试样拉伸应力的增加和材料屈服强度的降低有关。
It shows that the composites' tensile strength and elongation decrease while the hardness and friction coefficient increase with the addition content of graphite.
结果表明，随着石墨添加量的增加，复合材料的抗拉强度和伸长率逐渐下降，硬度逐渐上升，摩擦系数逐渐变大。
Tensile and microhardness tests show that the quality of joint is better and tensile strength of joint does not decrease greatly compared with that of parent material;
拉伸实验和显微硬度测试表明，接头质量良好，与母材强度相比，接头的抗拉强度未见有大幅度下降；
The results show a decrease of tensile strength and mean vertical anisotropy and an increase of plane anisotropy with a decreasing of the width of specimen.
结果表明随着试样宽度的减小，抗拉强度、厚向异性系数减小，板平面方向性系数增大；
To split tensile strength and flexural strength, with the increase of air content, strength increase firstly and then decrease.
对于劈裂抗拉强度和抗折强度而言，随着含气量的增加，强度先增加后减小。
The results showed that increasing of glycerol content can decrease the tensile strength and increase the elongation at break;
实验结果表明：甘油含量的增加会降低片材的抗拉强度，但升高其断裂伸长率；
With the increasing of mass fraction of PEG, membrane porosity and pure water flux become larger, and the maximum tensile strength and elongation at break of the membrane criterion decrease gradually.
随着PEG质量分数的增加，膜孔隙率与水通量变大，最大拉伸强度、断裂伸长率等力学性能逐渐减小。
The results show that tensile strength and yield strength increase generally, while total elongation and product of strength and ductility decrease with the increase of strain rate.
结果表明，随应变率的增加，抗拉强度与屈服强度总体呈上升趋势，而断裂伸长率及强塑积单调下降。
With the increase of notch root radius and the decrease of stress concentration coefficient, the tensile strength decreased.
材料的抗拉强度随着材料缺口半径的增加及应力集中系数的降低而降低。
The product with too high crosslinking degree could decrease the tensile strength and elongation of its modified PVC.
交联度过高的产品会降低改性PVC的强伸性能。
The results showed that the tensile strength and yield strength decrease while total elongation increases with decreasing quenching temperature.
结果表明，随着淬火温度的降低，双相钢的屈服和抗拉强度下降，同时总伸长率提高；
Yield strength and ultimate tensile strength, work hardening exponent and normal anisotropy of plastic strain ratio decrease but planner anisotropy of plastic strain ratio increases.
屈服强度、抗拉强度、加工硬化指数和塑性应变比厚向各向异性降低，塑性应变比平面各向异性增大；
Yield strength and ultimate tensile strength, work hardening exponent and normal anisotropy of plastic strain ratio decrease but planner anisotropy of plastic strain ratio increases.
屈服强度、抗拉强度、加工硬化指数和塑性应变比厚向各向异性降低，塑性应变比平面各向异性增大；
应用推荐