The corrosion resistance of epoxy adhesive was assessed by its tensile shear strength.
环氧胶粘剂的耐蚀性能是通过测定其拉伸剪切强度来评定的。
Finite element analysis software is feasible to simulate the failure analysis of tensile shear test, even partial replacement of shear tensile test.
证明用有限元分析软件对点焊结构进行失效模拟的可行性,甚至可以部分替代剪切拉伸试验。
The tensile shear properties, mass loss ratio and surface residual stress of the bond samples before and after the thermal cycling were measured. The tensile shear fracture morphologies were observed.
测试了热循环前后胶接试样的拉伸剪切性能、质损率和表面残余应力,观察了拉伸剪切断口形貌。
The principal tensile stress check is introduced in order to verify the adequacy of webs of segmental concrete girder Bridges for longitudinal shear and torsion.
主要拉应力检查旨在确认分段混凝土梁桥梁腹板用于纵向剪切与扭曲的充分性。
An applied tensile or compressive stress resolved into a shear component along a specific plane and direction within that plane.
一个实际拉或压应力沿某一特定平面和在该平面特定方向上分解得到的切应力分量。
Due to the heterogeneity, rock failure mainly results from tensile damage but shear damage still exists, which has influence on the shear strength.
由于试样细观缺陷非均匀性的存在,导致岩石断裂主要由拉伸破坏引起,但拉剪混合破坏仍然存在,并对抗剪强度有较大的影响。
Tensile strength and lap shear strength increased with increasing of grafting degree due to great improvement of polarity.
离聚体的拉伸强度、搭接剪切强度和乳化性能均随顺酐化程度的提高而改善。
The characteristic values of micro shear test and tensile test of alloy aluminium were determined and the quantitative expressions of these characteristic values were studied.
测定了铝合金的微型剪切试验和拉伸试验的性能参数,研究了这些性能参数之间的数量关系式。
Testing study is made on the basic mechanical property of thenardite salt rock, which includes uniaxial compressive, indirect tensile and Angle changed shear tests.
针对岩盐这一特殊性质的岩石,进行了基本的力学特性试验,包括单轴压缩、间接拉伸及变角剪切。
The results show that the tensile strength presents negative hybrid effect, while shear strength presents positive hybrid effect, and their hybrid effect decreases with the hybrid ratio increasing.
试验结果表明,拉伸强度表现出混杂负效应,而剪切强度表现出混杂正效应,两种强度的混杂效应都随混杂比的增大而降低。
Three typical manifestations of wafer bonding strength were introduced as tensile strength, shear strength and adhesive strength.
介绍了三种典型的圆片键合强度表现形式:抗拉强度、剪切强度和粘接强度。
This results in a much stronger bond that lasts longer and is much less susceptible to separation under compressive, tensile and shear forces.
粘接的结果增强了交联键强度,而降低了在压力、拉力和剪切力作用下,比较容易分离的现象。
Safety factors of rock, including shear safety factor and tensile safety factor, safety factor of lining and design calculation methods of tunnel are studied.
研究了隧洞围岩安全系数(剪切安全系数、拉裂安全系数)与衬砌安全系数的算法以及隧洞设计计算方法。
Based on the thought experiment (a well-known research method), the tensile and shear stresses are discussed on the sides of a rhombus due to a blasting.
本文借助于思想实验的研究方法,讨论了菱形边上拉剪应力变化特点。
The fatigue failure types of the beams were fracture failure, bending tensile failure and shear compression failure.
这批试件的疲劳破坏形式为:折断破坏、弯拉破坏和剪压破坏。
Meanwhile, shear strength, splitting tensile and flexural toughness experiments have been conducted using four types of steel fiber on steel fiber reinforced high strength concrete (SFRHSC).
此外,本文还利用不同类型钢纤维进行了钢纤维高强混凝土的抗压强度、抗剪强度、劈拉韧性和弯曲韧性试验。
Forces acting on the bone cells include compressive tensile stress and shear stress. The shear stress is the main force which can be sensed by the bone cells.
作用在骨骼细胞上的应力包括压-拉应力和剪切应力,剪切应力是骨骼细胞能感受到的主要应力作用。
Direct tensile, acceleration, and shock wave tests belong to the tensile test group, whereas adhesive tape, direct shear, peel and scratch tests belong to the shear test group.
直接拉离、加速和冲击波等方法属于拉力法,而胶带、直接剪切、剥离和划痕等方法属于剪切法。
The effect of dynamic shear and tensile strength of tungsten heavy alloys on the fracture mode of fragmentation under explosive loading was investigated.
研究钨合金动态抗拉和抗剪强度对爆炸加载下破片宏观断裂模式的影响。
Seismic stress is composed of compressive stress, tensile stress and shear stress.
地震应力主要有压缩应力、拉疏应力及剪切应力的复杂性;
The tensile and shear properties of F-12 aramid fiber and carbon fiber intem1y hybrid NOL ring composites are presented in this paper.
本文以NOL环研究了F- 12/碳纤维混杂复合材料的拉伸性能和剪切性能。
Forgings can withstand higher shear and tensile forces than the castings.
锻件比铸件能承受更高的剪切力和拉伸力。
Relatively comprehensive test study on the strength capacity of the reinforced concrete beam under bending moment, shear force and axial tensile force was carried out.
对弯、剪、轴拉复合受力状态下钢筋混凝土梁的承载能力进行试验研究。
As a result, it is understood that placing steel bar in the tensile area will improve the ultimate bearing capacity of the RCFT beam, and shear failure of filled concrete will be avoided.
结果表明,在梁的受拉区配筋可以提高梁的极限承载力,并且可以避免核心混凝土的剪切破坏。
Although it is really the diagonal tension for which shear reinforcing must be provided, diagonal tensile forces are not calculated.
虽然在这些部位剪切应力将会以斜拉应力的形式被提供,而斜拉应力是不可计算的。
Tightsen structural adhesives have excellent tensile, shear and peel strength combined with maximum impact, stress and vibration resistance.
泰盛结构胶具有较强的拉伸、剪切与剥离强度,耐冲击、耐压、抗振动。
Presumably it is due to their different critical values of the ratio of slip plane hardening rate to current tensile stress for shear localization.
这可能是由于在不同状态时产生剪切形变局部化的滑移面硬化率对瞬时拉应力的临界比值不同之故。
According to the hypothesis between tensile stress and shear stress relationship during sheet metal forming, a similar solution of the equations can be obtained.
根据板材塑性成形过程中的拉应力与剪应力关系的假设,可以得到力学方程的近似解。
Presumably, it is due to their different critical values of the ratio of slip plane hardening rate to current tensile stress for shear localization.
这可能是由于它们产生剪切形变局部化的滑移面硬化率对瞬时拉伸应力的临界比值不同之故。
Presumably, it is due to their different critical values of the ratio of slip plane hardening rate to current tensile stress for shear localization.
这可能是由于它们产生剪切形变局部化的滑移面硬化率对瞬时拉伸应力的临界比值不同之故。
应用推荐