To make accurate temperature measurements with thermocouples, the reference junction temperature must remain constant. If it varies, suitable compensation for these variations must be provided.
要用热电偶实现精确的温度测量，参考端温度必须保持恒定；如果会变化，必须提供这些变化的适当补偿。
The sensitive temperature characteristics of PN junction inverse saturation current is fully utilized to obtain good temperature coefficient and PSRR with simple circuit structure.
该技术充分利用了PN结反向饱和电流是温度敏感函数的特性，使用简单的电路结构，达到了很好的温度特性和电源抑制性能。
Should there be an uncompensated variation in the reference junction temperature, there will be a corresponding change in millivolt with a resultant error in temperature measurement.
假如参考端温度的变化没被补偿，就会有相应的毫伏电压变化，结果会导致温度测量的误差。
In the junction temperature measurements, we get reasonable curves and also confirm the accuracy of the system's measurements further.
在接面温度量测上，我们得到了合理的曲线，也进一步地确定系统量测的准确度。
There are two limitations on the power handling ability of a transistor: average junction temperature and second breakdown.
有两个限制了晶体管的处理能力，功耗：平均交界处的温度和二次击穿。
Methods the respiratory signal is detected by the characteristics of diode junction voltage with temperature changes.
方法：该电路利用二极管的结电压随温度变化的特性实现呼吸信号的检测。
This paper analyzes the failure mechanism of semiconductor P N junction temperature sensors and presents a new design to reduce the internal stresses and methods to improve the processes.
通过失效形式，分析了半导体P-N结温度传感器的失效机理，介绍了为降低内应力而进行的设计和工艺改进。
Device operational range is limited by the maximum junction temperature.
装置的运作范围是有限的最高结温。
This paper presents a well water temperature monitor, and its use of PN junction temperature sensor as temperature components, integrated circuits used for ICL7126 and other A / D converter.
本文介绍一种井中水温监测仪，其采用PN结温度传感器作为感温元件，用集成电路ICL7126等作A/D转换器。
The positive junction volt tends towards the build-up potential while temperature goes to 0K.
当温度趋向0K时，正向结电压趋向内建电势差。
PN junction temperature sensor is used. 16 temperature signs are acquired at the same time. Proceeded data can be indicated, printed or controlled.
系统选用PN结温度传感器，可同时测取16个温度信号，经数据处理后可实时显示、打印或控制。
Transistor thermal spectrum, as a new method, different from the commonly infrared thermogram, is introduced to characterize the non-uniform property of the junction temperature distribution.
晶体管热谱是表示晶体管结温不均匀性的一种与热像图不同的新方法。
In this study, we have set up a system to measure LED junction temperature.
在本研究中，我们建立了一套量测发光二极体接面温度的系统。
This paper introduces the PN junction sensor experimental system of temperature developed by the author according to the needs of teaching.
介绍了根据教学需要而设计开发的PN结温度传感器实验系统。
The relationship between the high peak power junction circulator and the bias magnetic field is described and a method to improve the temperature characteristic of this circulator is given.
阐述高功率结式环行器的温度特性与偏置磁场的内在联系，给出提高温度特性的方法。
Method: To choose best recipe and craft by doing experiment of face junction and survey its quality stability under the condition of chamber temperature and hasten experiment.
方法：采用正交试验的方法，选择最佳处方及工艺，并考察其室温条件下和加速试验后其质量稳定性。
The temperature behavior of the forward voltage VF of the P-N junction is discussed.
本文讨论了低温下P -N结的正向电压降v _ F随温度t变化的特性。
A method for measuring and controlling the junction temperature of power transistor during succession operation life test is proposed.
为了在试验周期中了解晶体管的结温，提出一种在功率晶体管稳态工作寿命试验过程中结温的测量与控制方法。
In this paper, the main factors which result in the temperature fluctuation are probed, and the method of the cold junction compensation of thermocouple is enumerated in common u.
本文探讨了温度波动的主要因素，列举了热电偶的冷端补偿的常用方法，叙述了在此问题上的技术发。
While one junction will adjust to the new ambient temperature quickly, another changes slowly, resulting in a temporary change in voltage offset.
一个结点已经迅速地调整到新的环境温度，而另一个结点则变化较慢，这样就产生了瞬时的电压偏置变化。
A new method for judging the running state of HV overhead transmission lines was put forward according to the temperature parameter of power cable junction.
提出了利用电缆接头温度参数来判断高压输电线路运行状态的方案。
In addition, Thermal Force-Directed Placement Algorithm is used, detailed analysis of the device optimized layout of the component junction temperature and the average PCB temperature are shown.
另外，本文还运用热力导向优化算法，分析了电子元器件的优化布局对元器件的结点温度的影响。
When a transistor dissipates power on work, its junction temperature distribution is commonly non-uniform.
晶体管在耗散功率时，结温分布一般不均匀。
This method needs the infrared camera to measure the surface temperature of junction bar, the measure precision is greatly influenced by the performance of infrared camera.
该方法需要使用红外热像仪测量汇流条表面温度，测量精度受红外热像仪性能影响很大。
The maximum acceptable junction temperature is different for C and I grade devices. If it is higher than the max. acceptable temperature, you may consider adding a heatsink or cooling fan.
C和I级器件允许的最高接合温度不同。如果温度高于允许的最高值，可能需要增加散热片或风扇。
The temperature of the voltmeter, and hence that of the material being measured by the probe, can be measured separately using cold junction compensation techniques.
利用冷接点补偿技术，伏特表的温度以及传感器探头反馈的温度可以被分别测量。
The temperature of the voltmeter, and hence that of the material being measured by the probe, can be measured separately using cold junction compensation techniques.
利用冷接点补偿技术，伏特表的温度以及传感器探头反馈的温度可以被分别测量。
应用推荐