At last, some methods of uncertainty analysis are listed, such as Monte Carlo method, Taylor method, probability trees and expert judgement method.
最后列举了不确定性分析的方法，即蒙特卡罗法、泰勒简化法、概率树法和专家判断法。
Secondly, we design an approximated delay feedback control method by applying Taylor theorem; it can make the controlled system stabilize the expected periodic orbits or equilibrium points.
其次，应用泰勒展开定理，设计了一种近似的延迟反馈控制方法，将受控的系统稳定到希望的周期轨道或平衡点上。
The new method firstly obtains two approximate rotational invariance relations about distributed sources central DOA by the Taylor series expansion of array steering vector.
新方法首先通过阵列方向矢量的泰勒级数展开获得关于分布源中心DOA的两个近似旋转不变关系。
To gain sevrial decision method of convex (concave) function by the definition of convex(concave) function and Taylor formula.
利用凸（凹）函数的定义和泰勒公式给出了凸（凹）函数的几个判别法。
The qualitative error analysis of the mechanical navigation system was implemented using Taylor series expansion method after introduction of the system characters.
在分析机构导航误差的基础上，提出用泰勒级数展开法对机构导航系统的误差进行定性分析；
Tthe application of Taylor window function in distance subsection weighting is given. The fact has demonstrated the feasibility of this method.
给出了泰勒窗函数在距离分段加权中的应用，事实已证明该方法的可行性。
A new method of polarity identification is presented, therefore the complex Taylor series is avoided, the efficient is improved and the procedure quantity is reduced.
提出一种新的极性识别方法，避免了复杂的泰勒级数运算，提高了运算效率，降低了程序量。
Using the method of Taylor series expansion's Gaussian iteration, intend to match the engineering experiment data in high accuracy.
利用泰勒级数展开的高斯迭代方法，高精度拟合工程实验数据。
By algebraic dynamical method, the exact analytical solutions of the ordinary differential equations are obtained in terms of Taylor series with local convergent radius.
用代数动力学方法求得了用泰勒级数表示的局域收敛的常微分方程的精确解。
The seven-grid difference format and nine-grid difference format of Helmholtz equation in right coordinate in the way of Taylor series method have been derived.
用泰勒级数法推出直角坐标系下亥姆霍兹方程的七点差分格式和九点差分格式；
In the present work, a method for solving the linear delay differential equations of the boundary-value function problem by using Taylor series is given.
本文对线性时滞微分方程边值函数问题提出一种级数近似解方法。
Its benefit is shown in comparison with the method of Taylor series.
在与泰勒展开方法的对比中，显示了该方法的优越性。
The traditional method of calculation for the acceptance parameters by Taylor expansion in three wave interactions is only suitable for the condition of small acceptance parameters.
采用传统级数展开方法计算晶体非线性三波互作用的允许参量。
This thesis adopts a gradient image registration method which is based on the Taylor theory. Since it can provide a good registration for big shifted image.
本文采用了基于梯度法的运动估计，因为它能很好地对大位移的图像进行精确的配准。
In chapter 7, an interval dynamic optimization method for uncertain structures using the improved 1st-order Taylor expansion is presented.
第七章针对区间参数振动结构提出了一种改进的动力响应的区间优化方法。
Based on the theoretical mathematical procedure, investigating the application of the Taylor -series method in bearings-only TMA.
以泰勒级数法的理论模型为基础，研究它在纯方位TMA中的应用问题。
A new method of polarity identification is put forward, therefore the complex Taylor series is avoided, the efficient is improved and the procedure quantity is reduced.
文中提出一种新的极性识别方法，避免了复杂的泰勒级数运算，提高了运算效率，降低了程序量。
Based on interval mathematics and Taylor series expansion, the interval analysis method is used to deal with uncertainties.
区间分析法是基于区间数学和泰勒展开的一种处理不确定性的方法。
Simulations showed that the performance of the proposed tracking method was better than the TDOA tracking method and the static location of Taylor series expansion algorithm.
实验证明，该方法的定位误差性能优于单纯的TDOA定位方法及静态定位方法中泰勒级数展开法的误差性能。
In this paper, Taylor series correction method was applied to mixed-mode problems.
本文把泰勒级数校正法用于混合型问题。
The precision of the signal generator is improved significantly with Taylor series corrected method.
通过对正弦波进行泰勒级数插值，使信号源的精度得到改进；
By comparing the results of Taylor test and computational simulation, a validating and optimizing method on dynamic constitutive model material constants was proposed.
通过实验数据和数值模拟结果的对比，研究了泰勒杆实验在材料动态本构关系参数确认和优化方面的应用。
By comparing the results of Taylor test and computational simulation, a validating and optimizing method on dynamic constitutive model material constants was proposed.
通过实验数据和数值模拟结果的对比，研究了泰勒杆实验在材料动态本构关系参数确认和优化方面的应用。
应用推荐