The batch controller also has a standard interface of RS-485 bus, preferably achieved the network design of the batch control system.
该配料控制器还配有标准的RS—485总线接口，较好地实现了配料控制系统的网络化设计。
PC is responsible for the management of the human-computer interface and real-time supervise of the control system. The motion controller performs all details of motion control.
PC机负责人机交互界面的管理和控制系统的实时监控等方面工作，运动控制器完成运动控制的所有细节。
Controller has RS-485, MODBUS standard field bus-bar communication interface and facilitate connect to switch board system.
控制器具有RS- 485,MODBUS标准现场总线通讯接口，方便接入只能开关柜系统。
The status and function of the LCD controller in the embedded system, and the liquid crystal displayer's interface signal's definition and function are introduced.
介绍了液晶显示控制器在嵌入式系统设计中的地位和作用，液晶屏接口信号的定义及作用。
On the basis of research on the bound ary-scan architecture and TAP controller, the paper implements a design for a t ap interface based on JTAG specification in a test system.
该文在研究边界扫描体系结构和TAP接口控制器的基础上，在一个测试系统中，实现了基于JTAG规范的主ta P接口设计。
The structure of the hardware and software of an aviation gyroscopic test system combined by industrial control computer, interface controller and test adapter is introduced.
介绍了工业控制计算机、接口控制箱、测试适配器组成的航空陀螺综合测试系统的硬件和软件结构。
Via Programming of programmable controller and testing of work-piece position by sensor, system running was controlled and fault was checked through man-machine interface.
通过可编程控制器编程，传感器检测工件位置，经人机界面控制装置运行、检测故障。
A method of how to use MATLAB Engine interface technology to add Fuzzy control in the Open CNC system based on the motion controller is introduced in this paper.
论文阐述了在基于运动控制卡的开放式数控系统中如何利用MA TLAB引擎接口技术来加入模糊控制的方法。
This controller system can link to PC by serial interface and can real-timely display data of all testing point.
该控制系统可以通过串口与计算机连接，实时显示各检测点数据。
Using the RS232 (9 pins) as serial interface can carry out the communication between computer and controller. This system adopts the binary form to transmit the data.
通过RS232（9）脚串口可实现计算机与控制器的双向通信，本系统采用二进制形式传输数据。
This paper will introduce the method of implementing the interface of data storage controller in the data storage system by using of the FLEX10K devices manufactured by ALTERA Corporation.
本文将介绍利用ALTERA公司的FLEX10 K器件，在数据存储器系统中实现数据存储控制接口的方法。
The control device for large bulb unit bearing oil system is ba sed on the programmable logic controller and programmable operator interface.
介绍了基于可编程序控制器和工业显示触摸屏的大型贯流式水轮发电机组轴承油系统控制装置的主要设计特点。
Based on the introduction of industrial Ethernet technique, this paper describes a method of expanding an Ethernet interface using RTL8019AS Ethernet controller in the 80c196 single-chip system.
该文在对工业以太网技术阐述的基础上，具体介绍了在80c196单片机系统中，利用RTL8019AS以太网控制芯片，实现工业以太网接口的硬件电路设计及软件设计。
The STD industrial controller is applied to the interface so that the module and flexibility of system are enhanced.
人机接口采用STD工控机，提高了系统配置的模块化和灵活性。
This paper mainly reviews three most important elements in a telepresence system: a force-reflecting manual controller, a virtual reality unit and an advanced operator interface.
介绍遥现系统中3个最主要的组成部分：力反馈手控制器、虚拟现实装置和高级操作者界面。
Difficulty of system Extending and transplant are found by means of PCI (Peripheral Component Interface) bus motion controller or PC (Programmable controller).
系统的扩展和移植难度发现的PCI(外设组件接口)总线运动控制器或PC(可编程控制器)的手段。
PLC is adopted as main controller and touch panel is used as the interface to observe and control the system.
系统采用了P LC作为控制部分的主控器件，将触摸屏作为系统观测和控制的界面。
The hardware of the monitoring system mainly consists of the DSP controller, nonvolatile memory, LED, clock management, keyboard interface, SCI communication units and CAN communication units.
系统的硬件部分主要包括了DSP微处理器的基本外围电路、非易失性存储、LED显示、时钟管理、键盘接口，以及SCI通信和CAN通信等单元电路。
The hardware of the monitoring system mainly consists of the DSP controller, nonvolatile memory, LED, clock management, keyboard interface, SCI communication units and CAN communication units.
系统的硬件部分主要包括了DSP微处理器的基本外围电路、非易失性存储、LED显示、时钟管理、键盘接口，以及SCI通信和CAN通信等单元电路。
应用推荐