Solve the surface shrinkage of plastic products completely.
彻底解决塑料产品的表面缩水现象。
The causes and relative factors of the surface shrinkage trace for injected products are discussed, and the design ideas of preventive and remedial measures are presented.
探索注塑制品表面产生缩痕的成因及其相关因素，提出了预防性设计思想及补救措施。
The textile fiber surface causes its lining because to wash not easily smoothly causes the shrinkage distortion.
纤维表面光滑使其面料不容易因洗涤而引起缩水变形。
SINK: Surface discontinuity, depression or dimple caused by non - uniform material shrinkage.
凹槽：由材料收缩不一致引起的表面中断，下陷，凹洞。
Ingot defects may be broadly classified into internal flaws and surface flaws. Internal flaws are caused by shrinkage.
钢锭缺陷广义上可分为内部缺陷和表面缺陷。内部缺陷是因收缩引起的。
Surface of the adaptor case should no scratch , . no shrinkage mark, flash and mechnical damage.
外壳表面应平整无划痕、缩水纹、毛刺及其它机械损伤。
Mix: can be used with all kinds of surface active agent, also suitable for early shrinkage and synthetic resin body and mixed enzymes.
混用性：可与各类表面活性剂混用，也适宜与合成树脂初缩体及生物酶混合使用。
Batch production shows there are no shrinkage cavity and porosity in casting, and no blowholes and sand inclusions on the top surface. The yield of the casting is 81%.
经批量生产验证，铸件内无缩孔、缩松缺陷，上表面无渣孔、气孔缺陷，工艺出品率81%。
It has been analysed the causes for the heavy surface spalling of back-up roll for a finishing mill. The result shows that the main causes are gas hole, shrinkage and bad heat treatment.
对连轧机精轧支承辊大面积剥落的原因进行了深入的分析，结果表明，轧辊内部的缩孔、气泡及热处理不当是造成轧辊表面剥落的主要原因。
In the cross section of square billet, the shrinkage values in the center of billet surface and billet corner are obviously bigger than that in the off-corner.
在方坯横截面上，铸坯表面中心和角部的收缩量明显大于偏角部。
Shrinkage: Cause of the low temperature from a supplement so that the surface of the cast that being cooled will be shrunk. Just like the shrinkage of the raiser.
缩孔由于补充温降所造成的收缩，以致最后冷却的铸件位置极易形成表面低陷的缩孔，类似冒口的缩孔。
It also can be sprayed on the surface of concrete members as a curring agent, and have a good shrinkage reducing effect.
也可以作为一种养护剂喷涂到混凝土构件与制品的表面，同样具有很好的减缩效果。
The shrinkage has wrinkled parts of the moon's surface like a raisin, creating pinched formations called lobate scarps…
月球的收缩使月球部分表面像葡萄干那样起皱，从而形成为“瓣状陡坡”…
Fracture energy, strength, shrinkage and expansion properties of cement mortar are studied under different moisture content and surface tension solutions.
以水泥砂浆为研究对象，对不同水分含量及不同表面张力溶液下砂浆的断裂能、强度及收缩膨胀性能进行了研究。
Ultra light high strength, thermal insulation, waterproof, and the surface adhesion strong, activist and arch, not crack, dry shrinkage ratio as well as good.
超轻高强、保温隔热、防水防潮、与基面结合力强、集体性好、不起拱、不裂缝、干缩比好等优点。
Using self-feeding in solidification can make good surface quality, no shrinkage casting defects of castings; the technology product yield of the casting greatly increases.
利用凝固过程自补缩，可使铸件表面质量好，无缩孔、缩松等铸造缺陷，工艺出品率大大提高。
The casting is easy to suffer from deformation, surface sink and internal shrinkage.
该铸件容易变形和产生表面缩凹、部缩孔。
Unbound aggregate base can efficiently retard the reflexion of cracks to asphalt pavement surface, which is aroused by the shrinkage crack of semi-rigid base in the inverted structure.
半刚性基层沥青路面作为过渡层时，可以有效改善半刚性基层收缩裂缝的反射裂缝的发生。
When the shrinkage of the rod fracture surface much more than that of the cup part fracture surface, its formation by compound extrusion is not applicable.
当杆的断面收缩率比杯形部分断面收缩率大得较多时，不适合直接用复合挤压成形。
Arid areas to prevent and reduce the individual caused by wood shrinkage cracking and surface cracking of wood at the end and so on.
可防止和降低个别干旱地区因木材缩水所引起木材末端干裂和表面龟裂等现象。
It produces moldings with good surface finish, is resistant to chemicals and stress cracking, and has low shrinkage and warpage.
它生产的模具表面光洁度好，可耐化学品和应力开裂，并具有低收缩和翘曲。
The shrinkage factor increases with the increase of specific surface area and the amount of banded water in hardened cement pastes.
收缩率随着水泥石比表面积、结合水含量的增加而增加。
Throughout the drying process, the surface of the free shrinkage strain is the largest, the more close to the core layer the smaller the free shrinkage strain.
在整个干燥过程中，表层的自由干缩应变最大，越靠近芯层自由干缩应变越小。
The shrinkage behaviors of TiO2 were investigated to clarify the effect of specific surface area on the densification behaviors at the initial sintering stage.
为阐明比表面对无压烧结初期致密化行为的影响，研究了氧化钛陶瓷的烧结收缩行为。
The capillary pressure which is the effect of the water loss from the concrete surface, is the origin of the plastic shrinkage in concrete cracking.
由于这种裂缝是由于混凝土塑性收缩引起，所以称之为塑性收缩裂缝。
The capillary pressure which is the effect of the water loss from the concrete surface, is the origin of the plastic shrinkage in concrete cracking.
由于这种裂缝是由于混凝土塑性收缩引起，所以称之为塑性收缩裂缝。
应用推荐