Secondly, influence of surface polish and glycol additive on pressurized water dielectric is studied.
其次，进行了抛光电极表面和添加乙二醇对加压水介质击穿影响的研究。
Surface Polishing: Seeking smooth surfaces, artisans polish articles three times with grit or charcoal. The work requires extreme care.
表面抛光：寻求表面光滑，工匠波兰文章三倍的砂砾或木炭。这项工作需要格外小心。
Aluminum Oxide Specific gravity 2.4 Moh hardness 3. More a filler than an abrasive. Tends to fade, but has good wear resistance. Will polish the opposing surface.
氢氧化铝比重2.4莫氏硬度3。比磨料加得更多的填充物。有衰退趋势，但耐磨性好。将抛光对偶。
It can be heated or cooled; inner surface adopts mirror polish, no dead Angle, and closed design to ensure material in asepsis condition.
可加热、冷却，内表面采用镜面抛光，无卫生死角，全封闭的设计确保物料始终处在无菌状态下。
On the basis of the model, we found ways to release the primary shaft vibration's influence on the quality of the polish surface.
在理论分析的基础上，提出减轻由主轴的振动引起的抛光表面质量问题的方法。
The shape dainty and cute: Suit white yarn that win high waist, yarn surface and loins' sell at a discount to polish a shape proportion.
身材娇小玲珑者：适合中高腰、纱面、腰部打折的白纱，以修饰身材比例。
With the fine metal polish, mini electric drill and cotton bud can be used to clean the metal surface, and the effect is good.
用微型电钻和棉签配合精细金属抛光膏，可用于清洁金属表面，效果很好。
Use an appliance wax polish on the inside surface between the doors.
在柜门之间的内表面上，使用蜡光剂。
In winter, many people in the maintenance of furniture, would give furniture wax, the industry source said: furniture polish wax before use, to check the paint surface is intact.
冬天，很多人在保养家具时，都会给家具上蜡，有关业内人士说：家具在使用上光蜡前，要检查一下漆层表面是否完好无损。
Surface must be completely cleam. dry and free of dust and oil. If applieed on plastic, polish the surface with sand paper to make it rough.
接合面必须清洁，干燥，无灰尘或油污，若是塑料物件，应先用砂纸打磨其表面，使之粗糙。
The magnetic abrasive machining is a method that the magnetic field is used to polish the surface of the workpiece.
磁研磨是利用磁力的作用进行表面抛光处理的新方法。
If the set collar end hardness is lower than HRC40, should first on the end surface again a built-up welding hard alloy, after the polish repackaging.
如果固定环端面硬度低于HRC40，则应先在端面上重新堆焊一层硬质合金，经磨光后再装配。
The uniformity of surface color and polish resistance can be improved significantly by effective post-processing.
经有效的后处理可使其表面色彩更均匀，耐磨性明显提高。
In order to achieve an ultra-fine mirror surface of mould for optical disk, diamond abrasive was adopted to polish the mould surface.
为了获得超光滑光盘模具镜面，选用金刚石磨料抛光光盘模具。
Finish painting before, you may need to gently polish the surface.
涂装面漆前，可能需要轻轻打磨表面。
Don't polish your crystal ball. If the surface is too shiny, all you'll be able to see in it is your own reflection.
没事别老擦拭你的水晶球，如果表面过于光亮，你只能看到心中的倒影。
For a bright glossy surface on your anodized part, steel wool or wet sand it and then polish it with a buffing wheel using tripoli compound.
需要明亮的光泽，则需要用钢丝球或者湿的砂纸磨，之后用硅藻土抛光轮抛光。
Move the crystallizing machine onto the surface, first move left and right then move up and down. Polish until the floor becomes glossy and lustrous. Each operation covers about 3~5 square meters.
在地表上以先左右后上下的顺序移动晶面机，研磨直到地表光亮，每次操作区域35平米。
Mold requiring sensitive surface as mirror polish, creping, EDM. Such as transparent case, OA electronics, Engineering resin products etc.
可用于对镜面性、蚀花性、放电加工性要求高的模具，如办公用具、透明外壳、各种树脂产品等。
Mold requiring sensitive surface as mirror polish, creping, EDM. Such as transparent case, OA electronics, Engineering resin products etc.
可用于对镜面性、蚀花性、放电加工性要求高的模具，如办公用具、透明外壳、各种树脂产品等。
应用推荐