Surface morphologies of coatings prepared by SPPS presented obvious layer structure.
SPPS法制备的涂层表面形貌呈现明显的层状结构。
The wear surface morphologies were surveyed by scanning electron microscope (SEM) and wear mechanism was analyzed under the sand slurry wear condition.
运用扫描电镜观察了这几种材料在泥沙磨损条件下的磨损表面形貌，分析了它们的磨损机理。
Surface morphologies were observed by scanning electron microscopy (SEM), and X-ray diffraction (XRD) was used to analyze the crystal corrosion products.
采用扫描电子显微镜(SEM)观察表面腐蚀形貌，XRD进行腐蚀产物分析。
The film and its surface morphologies of amino-polysiloxane were observed and studied by means of atomic force probe microscopy(AFM) and contact angle measurement instrument.
应用原子力显微镜（AFM）和接触角测量仪对乙酸酐改性氨基聚硅氧烷的成膜性及膜形态进行了研究。
Meanwhile, through simply adjusting the side chains, we successfully achieved different surface morphologies of the nanocages and control of their surface distribution behavior.
同时，通过简单的化学修饰改变此系列笼状分子的侧链结构，我们可以实现在极性基底上对笼状分子表面分布行为的控制。
The surface morphologies in different regions are obviously non-uniform, and the material density of the aggregates near the sample edge is larger than that in the centre region of the sample.
在样品的边缘与中心区域形貌不一致，样品边缘区域的凝聚体的数密度要大于中心区域的数值。
The surface morphologies exhibit deformation wear in the middle and micro cutting wear in the sides, which indicate that all the samples exhibit ductile material characteristics in the erosion.
合金丝试样中部为变形磨损，侧面为微切削磨损，表现为典型的韧性材料冲蚀磨损特性。
Surface morphologies and microstructures of the whisker were characterized by using SEM, HRTEM and SCXD. The preferential growth orientation of the whisker was determined to be along its direction.
通过SEM、HRTEM及SCXD等表征手段，对晶须的表面形貌和微观结构进行了分析，并确定其生长方向为晶须的方向。
The results indicate that the change in fractal dimension is directly proportional to the surface quality, but the roughness can′t be used to describe the morphologies of film surfaces perfectly.
结果表明，分形维的大小与薄膜表面质量成正比，而表面粗糙度不能全面描述薄膜表面形貌；
Using SEM with EDX analysis, the composition, microstructure and morphologies of the surface layer were analyzed.
应用SEM电镜分析和能谱分析等方法分析了热浸扩散渗铝层的成分、组织和形貌。
Nanocopper particles were prepared by flow levitation method. The structures, morphologies, granularities and the surface oxide layers of particles were investigated by TEM, XRD, and AES techniques.
采用自悬浮定向流法制备金属铜纳米微粒，并用TEM,XRD和AES等分析手段研究了铜纳米微粒的形貌、粒度、结构及其表面氧化层特性。
The tensile shear properties, mass loss ratio and surface residual stress of the bond samples before and after the thermal cycling were measured. The tensile shear fracture morphologies were observed.
测试了热循环前后胶接试样的拉伸剪切性能、质损率和表面残余应力，观察了拉伸剪切断口形貌。
AFM, SEM equipped with EDX and optical microscope were employed to observe and analyze the morphologies of the surface, cross-section and wear scar of the coatings.
利用原子力显微镜(afm)、扫描电镜(sem)和光学显微镜观察分析了硫化亚铁喷涂层的表面、截面与磨面形貌。
The surface profiles, micro-morphologies and crystal quality of SSP ribbon and Poly-Si film were then investigated by the step profiler, XRD (X-ray Diffraction) and SEM (Scanning Electron Microscopy).
借助台阶仪、X射线衍射(XRD)、扫描电镜(sem)等手段对颗粒硅带及多晶硅薄膜进行了表面轮廓、结晶质量和微观形貌的表征。
For films on water surface, the concentration of polymer solution, sort of annealing vapor and annealing time were discussed to modulate films' morphologies.
对于水上成膜，主要研究了聚合物浓度，不同溶剂场处理，不同后处理时间对聚合物形态的影响。
For films on water surface, the concentration of polymer solution, sort of annealing vapor and annealing time were discussed to modulate films' morphologies.
对于水上成膜，主要研究了聚合物浓度，不同溶剂场处理，不同后处理时间对聚合物形态的影响。
应用推荐