However, the moisture content of the mat had little influence on the surface layer temperature.
板坯含水率对表层温度的影响较小。
The effecting factors of grinding field temperature were analyzed. The law of roller surface layer 's temperature was researched.
系统分析了影响磨削区温度的因素，探讨磨削轧辊表层温度的分布规律。
Second, for cooking utensils, cooking in low temperature or cooking in high temperature after spread a layer of firm oil on the surface of cooking utensils.
其二，在锅具方面解决，比如降低烹饪温度；在锅具表面涂一层比较牢固的油脂后，再在较高温度下烹饪等。
Humidifying treatment in mat surface could shorten a half time when the temperature of core layer reached to water vaporizing temperature at most.
板坯表面增湿处理，能使其中心层到达水分汽化温度的时间最多缩短约一半。
The results show that the variation of the scaling layer surface temperature is one of the major factors that cause the asymptotic tendency of scaling process.
结果表明，对恒壁温情况必须考虑垢层表面温度随时间的变化，这一变化是导致结垢过程渐近特性的重要原因之一；
A heat mass transfer model is constructed to take the variation of the scaling layer surface temperature into consideration.
据此提出了考虑垢层表面温度变化的描述结垢过程的传热传质模型。
Though infrared thermoscope is used to detect the temperature of billet when it is taken out of the stove, precision is still affected because of the oxide layer on the surface.
尽管钢材出炉时，可用红外线测温仪来进行钢材表面温度检测，但因钢材表面存在氧化层，也影响钢材温度检测精度。
Global warming is defined as the rise of the average temperature of the Earth's near-surface layer of air as well as the oceans, and extends to the projected continuation of that rise.
全球气候变暖的定义是崛起的平均气温的地球近地表层的空气，以及海洋，并延伸到预计的延续，即上升。
The effect of mat moisture content on the surface and central layer temperature was investigated.
研究了施胶板坯的含水率对刨花板热压过程中表、芯层温度的影响。
The width and surface temperature of the radiation surface are directly related to the thickness and material of the filling layer.
辐射面的宽度、表面温度与填充层的厚度和材质有直接关系。
Simultaneously, defects in the passivation layer of the device surface are also increased with the increasing of the baking temperature and also the surface recombination velocity.
同时芯片表面钝化层内的缺陷数目也在温度作用下增加，引起芯片表面复合速度增加。
The thickness of diffuse layer and the surface roughness of molybdenum alloying layer increase with increasing the Ti6Al4V base temperature.
随着基体温度的升高，扩散层的厚度增加，并且合金层表面粗糙度增大。
The adiabatic heating induces the temperature of fracture surface layer to be higher than the liquidus temperature too.
计算表明，断口表面层绝热升温温度依然高于液相线温度。
This paper discusses the burn of ground surface layer in the view of surface integrity and demonstrates that the governing factor of influence is grinding temperature.
本文从加工表面完整性观点讨论了磨削表面层烧伤的实质，指出影响烧伤的主导因素是磨削温度。
Through measuring meteorological parameters including temperature, humidity, pressure and wind speed, atmospheric turbulence strength in the surface layer can be obtained.
通过测量近地面层不同高度处温度、湿度、压强和风速等常规气象参数，结合模型可给出近地面层大气湍流强度。
Under the conditions of the high air temperature and humidity, the average frost density is raised significantly due to the appearance of the water droplet on the frost layer surface.
而对高温、高湿度工况，霜层表面出现了首先形成凝结水滴的现象，使得霜层密度大大增加。
Research results show:(1)the original temperature field of cement layer surface were quickly destroyed in initial coil pipe leakage, while the changes of floor surface were weaker;
研究结果表明：（1）盘管泄漏初期，水泥层表面原始温度场迅速被破坏，而整个地板表面变化较弱；
In the vertical direction the temperature gradient of surface layer is the greatest. The thermophysical properties of the facial material play an important part in the heat storage of the kiln car.
在窑车垂直方向上，靠近车台面处的温度梯度最大，车台面衬料的物性对窑车蓄热量的大小起着重要的作用。
As a powerful pulsed laser irradiate a solid material, the plasmas layer of high-temperature and high-pressure would be formed in the incident surface of target instantaneously.
脉冲强激光辐照固体靶材时，瞬间即可在靶材辐照面形成一个高温高压的等离子体层。
The daily change of air humidity in surface layer is contrary to that of temperature.
近地层空气湿度的日变化与温度相反。
In winter, the vent is shut down. By the greenhouse effect, the air in inter layer is heated and temperature at internal surface increases, and then energy-saving effects is achieved.
冬季关闭出风口，利用温室效应加热中间层的空气，提高内表面温度，达到节能效果。
The results show that when the temperature is about 1000K, the vacancy in the second layer begins to diffuse to the surface.
结果表明，当温度为10 0 0K左右时，位于近表面第二层上的空位开始向表面运动；
70% sulfuric acid at room temperature and a short period of time can only dissolve the surface layer of fiber.
70%的硫酸在室温下和较短的时间内只能溶解纤维表面一层。
In past literature, based on the layer's hardness close to martensite's, the layer was considered martensite from abnormal temperature rise on the surface.
在以往的文献记载中，常根据其硬度接近马氏体，将其归结为拉拔过程中表面异常升温而产生的马氏体。
In past literature, based on the layer's hardness close to martensite's, the layer was considered martensite from abnormal temperature rise on the surface.
在以往的文献记载中，常根据其硬度接近马氏体，将其归结为拉拔过程中表面异常升温而产生的马氏体。
应用推荐