Irradiation graft copolymerization becomes a green and important synthetic strategy for surface functionalization and facile preparation of new organic biomedical materials.
射线辐射高分子材料表面接枝共聚合是一种绿色的、重要的有机生物材料合成制备方法。
Possibility to dope Y2O3 particle on the surface of superalloy sample and the relationship between homogeneity and irradiation parameters of laser have been investigated by means of laser irradiation.
本文通过激光辐照的方法，研究了在高温合金试样表面掺杂Y_2O_3质点的可能性、均匀程度与激光辐照参数的关系。
The surface modification of natural rubber (NR) was carried out by grafting polyorganosiloxane under microwave irradiation.
微波辐照下，用聚硅氧烷对天然橡胶表面进行了处理。
The results showed the crystalline surface had effect on the irradiation crosslinking of PA1010, and the damage dose to the crystal increased with the increase of the crystalline surface area.
结论如下：结晶表面影响PA1010的辐射交联，结晶的破坏剂量因结晶表面积增大而提高。
The surface modification methods of UHMWPE fibers are described in this paper, especially the advantages, mechanisms and techniques of photocrosslinking and photo grafting by UV irradiation.
本文对UHMWPE纤维的表面改性方法进行了概述，重点介绍了紫外辐照交联和紫外光接枝改性的优点、机理和工艺，并提出了目前紫外辐照改性中尚存的问题。
This paper deals with an effective method of laser contact irradiation on cancer of body surface in which its temperature is controlled by a computer.
介绍一种计算机测温，激光接触照射恒温治疗体表肿瘤的一种行之有效的方法。
The reaction mechanism of pyrite surface under the irradiation of electron beam is analyzed.
并对电子束辐照条件下黄铁矿表面反应机理进行了分析。
By irradiation of UV light, the surface activities of azo derivatives were significantly changed.
在U V光照射下，偶氮衍生物的表面活性有重大改变。
The results showed that irradiation effect of high energy protons on the optical surface stability and the reflective property was not obvious.
高能质子辐照没引起面形明显变化。高能质子辐照对反射光谱特性没有影响。
Main driving factors include surface condition, heat treatment, alloying composition, presence of second phase particles and irradiation.
在疖状腐蚀的影响因素方面，认为主要有表面影响、热处理影响、合金成分影响、第二相影响、辐照影响等。
After plasma irradiation, the specimen surface morphology was observed by SEM and the element composition of the coatings was analysed by XPS.
经过若干次等离子体放电实验后，取出样品进行表面形貌、表面元素成分及深度分布的X射线光电子能谱分析。
The results are listed as following: 1 the top surface layers of CRIC and 316l SS sample were remelted under the irradiation of HCPEB. Crater-like morphology was formed on the treated surfaces.
冷轧工业纯铜及316L不锈钢处理样品表面均发生重熔现象，处理面上形成类似火山坑的显微形貌。
The carrier concentration of surface after CO2 laser irradiation can exceed the solid solubility limit.
经过激光处理后样品表面一薄层载流子浓度超过了杂质的固溶度极限。
Results show that with the increase of the irradiation time the density of the film increases while surface roughness decreases, and the refractive index increases.
结果表明：随着曝光时间的延长，膜的致密性增加，表面粗糙度下降，折射率增大。
Polymer membrane surface may occur grafting reaction by the UV-irradiation, so that the properties of membrane surface could change a lot.
高分子膜表面在紫外光辐照下可能发生光接枝反应，从而使高分子膜的表面性质发生很大的变化。
Nano-TiO2 retarded the degradation of PPS chains to form oligomers caused by UV irradiation, but caused more -OH group in the surface of PPS composites.
纳米氧化钛的加入抑制了因紫外光引发造成的聚苯硫醚分子链的降解。
Nano-TiO2 retarded the degradation of PPS chains to form oligomers caused by UV irradiation, but caused more -OH group in the surface of PPS composites.
纳米氧化钛的加入抑制了因紫外光引发造成的聚苯硫醚分子链的降解。
应用推荐