By selecting a group of suitable entrance parameters, a submerged inlet with the trapezoid entrance on the plane surface is designed and verified.
通过选取一组合适的入口参数，设计了一种在平面上具有梯形入口的水下入口，并进行了验证。
Then by selecting a group of suitable entrance parameters, a submerged inlet with the trapezoid entrance on the plane surface is designed and verified by wind tunnel tests.
在此基础上，选择一组口面参数设计了一梯形进口的平面埋入式进气道方案，并进行了高速风洞试验验证。
Retractable blowers shall be provided for the convection evaporative surface (third pass) and inlet to the superheater.
应为对流蒸发面(第三通道)和至过热器的出口进口提供伸缩式吹灰器。
The numerical algorithm was verified by calculated and experimental data for a finite width wedge and extemal compression surface of a convergent inlet.
数值算法是通过收敛形进气道的有限宽楔形外压缩表面的计算和实验数据来验证的。
The flowing and heat transfer in the primary surface recuperator (PSR) can be influenced by unreasonable inlet structure which results in uneven material flow distribution.
不合理的进气结构造成一次表面回热器(PSR)内部物流分配不均匀，影响回热器内部流体的流动和传热效果。
The control strategy for surface temperature of the core rod is investigated and the scheme of introducing advanced compensation on the quantity of inlet water by gradient function is stated.
对芯棒表面温度的控制策略进行初步探讨，提出引入梯度函数对进水量提前补偿修正的方案。
The suction facilities include the pipeline from the suction fluid surface to the inlet of the pump and valves and fittings.
吸入装置包括吸入液面至泵进口处的管路、阀件等。
The outer casing superior surface, forms the configuration of the suction inlet, are inclined to the downwards.
形成吸入口外形的外壳上表面为朝前向下倾斜的状态，上表面有反射部分。
A detailed numerical simulation study was conducted of the flow distribution in the heating surface tubes of a boiler roof superheater featuring a distribution header with a bent inlet.
对一台锅炉中其分配集箱带弯头入口的顶棚管过热器受热面管流量分配做了较详细的数值模拟研究。
The influences of applied magnetic field. inlet velocity profile, initial surface disturbance and surface tension on interface shape were analyzed.
通过对方程的数值求解，研究了外加磁场强度、进口速度分布、初始表面扰动对界面形状和界面张力的影响。
Inadequate submergence can result in pre-rotation of the water in the wet-well, resulting in the formation of strong free-surface air core vortices and the entrance of air into the pump suction inlet.
潜水不恰当可能导致湿井内的水预旋转，导致形成强烈的自由表面空气中心漩涡，并使得空气进入泵的吸入进口管道。
There are small temperature and pressure difference in steam inlet and outlet of heat exchanger, and big heat transfer surface.
换热器蒸汽入口和出口温差小，压差小，管程传热面积大。
Let's make the surface for the air inlet.
让我们使表面为空气进气口。
The recess is preferably formed so as not to provide fluid, communication, from the inlet to the outlet across the rotor end surface.
所述凹部优选地这样形成，以使得流体不会经由凹部从腔室入口到 腔室出口横跨转子端面地流通。
While the pressure difference between the inlet of fracture and the outlet of fracture is constant, the transmissibility of fracture surface will decrease with the rising fractal dimension.
在对裂隙两端施加相同压力差的条件下，裂隙面的等效导水系数会随着分形维数的增加而降低。
The uniform design and response surface methodology(RSM) are applied to the multi-objective optimization of a 2-D mixed compression scramjet inlet.
基于响应面法进行了二维混合压缩超燃冲压发动机进气道的多目标优化研究。
The circulation inlet port is designed so as to enable the introduction of water into the reservoir tangentially to the surface.
流通进气道的设计，从而使引进的水进入水库切到地表。
The circulation inlet port is designed so as to enable the introduction of water into the reservoir tangentially to the surface.
流通进气道的设计，从而使引进的水进入水库切到地表。
应用推荐