The container may burst up if you superheat it so much.
如果你这样过分加热的话,这容器会爆炸。
To achieve the low superheat casting, a kind of cooling nozzle is developed.
为实现低过热度浇注,开发了一种冷却水口。
Otherwise, the solidification structure for different superheat was simulated.
在此基础上还模拟了不同过热度下铸坯的凝固组织。
Maximum wall superheat does not always exist at the top of the boiling surface.
壁温过热度沿高度分布存在极大值,且该极值并不总在通道顶部;
The effect of the superheat is much slighter than that of above mentioned factors.
与上述因素相比,过热度的影响很小。
Low superheat casting is the important method of increasing equiaxed crystal ratio of bloom.
降低钢水的浇注过热度是提高连铸坯等轴晶率的有效措施。
For a single system, the increase of superheat degree would increase the solubility of aluminum.
对于某个特定体系来说,提高过热度会增加铝的溶解度。
Some key parameters such as superheat, initial water temperature and water level have been studied.
实验研究了过热度、初始水温及水位高度对方腔内池水瞬态闪蒸时间的影响。
There the hot gases leaving the flame region superheat the saturated steam produced in the boiler section.
热气从火焰区出来,对锅炉管道里产生的水蒸气进行过热。
However, excessive P addition results in a larger degree of superheat of the melt, hence aggravating the oxidation.
但当P过量时, 则会因熔体过热倾向明显而加剧氧化;
The results show that the steel liquid is cooled down by cooling roller and the pouring with low superheat is realized.
结果表明:经冷却辊冷却的钢液过热度降低,实现了低过热度浇铸的目的。
Furthermore, casting speed, superheat and cooling waters effects on steady temperature field are analyzed in this paper.
此外还分析了拉速、过热度和冷却水量等因素对稳态温度场的影响。
The compensation scheme for the density of superheat steam and the new density compensation formula are introduced in detail.
详细介绍过热蒸气密度补偿方案及新的过热蒸气密度补偿式。
Molten melt superheat treatment is an effective means for microstructure refinement and advancement of alloy mechanical property.
熔体过热处理是细化组织提高合金力学性能的有效途径。
Influence factors, such as liquidus temperature, superheat degree, electrolyte components, and the depth of molten salt were focused.
主要研究了初晶温度、过热度、电解质组成,以及电解质融化之后的熔盐深度对铝溶解度的影响。
The paper presents a dynamic performance identification for superheat steam temperature control systems of boiler using ANN approach.
提出了基于BP网络的锅炉过热器温度控制系统动态特性的辨识方法。
The steel liquid superheat, velocity and rule of secondary cooling are important process parameters influence on billet internal quality.
钢水过热度、拉速和二冷制度是影响铸坯内部质量的重要工艺参数。
The cell ledge seriously impacts on current efficiency in aluminium production and the superheat of electrolyte greatly links with the ledge.
铝电解槽炉膛内形严重影响着电流效率,而铝电解槽的炉膛内形与电解质的过热度有很大的关系。
The influence of the different superheat degrees on solidification structure of the Al-5%Cu alloy by electric pulse modification was studied.
研究了不同的过热度对电脉冲孕育处理Al-5%Cu合金凝固组织的影响。
As the superheat temperature being enhanced, the size of carbides eutectic cells increases and tensile properties decline at room temperature.
随着过热度的增加,碳化物共晶团的尺寸增大,导致室温拉伸性能降低。
A new hypothesis is proposed in the paper to determine the superheat limit of liquid on the basis of fluctuation theory of statistical thermodynamics.
本文利用统计热力学涨落理论提出一个新的假说,并由此建立了确定液体极限过热度的新方法。
The influences of hysteresis and relaxation of melt superheat on the morphological stability of interface in directional solidification were described.
熔体过热处理的弛豫过程和引起的不可逆过程使熔体状态变化出现滞后效应,从而影响定向凝固界面形态稳定性。
Experimental study allows us to correlate the flashing duration time with the superheat and the initial water level as well as the initial water temperature.
实验研究了过热度、初始水温及水位高度对方腔内池水瞬态闪蒸时间的影响。
Besides the cell voltage, bath temperature and bath ratio, the inputs of the system also include the liquidus temperature, superheat extent and cathode voltage.
系统的输入参数除传统的电压、温度和分子比外,还采用初晶温度、过热度和阴极压降等作为系统的输入参数。
Based on the experiments, the variation rule of the sensitive physical properties of AlSi alloy melt was studied under the conditions of modification and superheat.
本文在试验基础上研究了铝硅合金熔体在变质和过热条件下敏感物性的变化规律。
Vapor-liquid heat exchangers are often used to superheat the suction vapor of compressor and to subcool the inlet liquid of throttle valves in refrigerating system.
制冷循环中往往采用回热器,使压缩机吸气过热和膨胀阀入口液体过冷。
Regressive analysis shows segregation index has maximal relationship with water ratio in secondary cooling, and has low relationship with superheat degree of steel.
回归分析表明偏析指数与二冷比水量的相关性最大,而与钢水过热度的相关性不强。
Regressive analysis shows segregation index has maximal relationship with water ratio in secondary cooling, and has low relationship with superheat degree of steel.
回归分析表明偏析指数与二冷比水量的相关性最大,而与钢水过热度的相关性不强。
应用推荐