Stroke control mechanism for the regulation and precise control of valve opening and closing position.
行程控制机构，用以调节和准确控制阀门的启闭位置。
Four-stroke engines of this type with this same type of intake valve motion but with a supercharger to make up for the loss of power density are known as Miller cycle engines.
四冲程发动机本与此同进气阀运动类型的类型，但以使增压器的功率损耗密度，这些都是为米勒循环发动机众所周知的。
This is a new type of slurry substance stop valve, which has shorter stroke, least rising power, better sealing effect, and vulnerable part has longer using age.
介绍一种提升距离短，提升力小，密封效果好，使用寿命长，适用于输送含有固体颗粒介质的新型截止阀。
During the intake or admission stroke, the piston moves downward as a charge of combustible fuel and air is admitted into the cylinder through the open intake valve.
在摄入或中风入院，活塞动作，作为燃料和空气中可燃负责向下是进入气缸通过公开承认，进气阀。
When the piston reaches the bottom of the intake stroke, the intake valve closes, trapping the air-fuel mixture in the cylinder.
当活塞到达进气行程的下止点时，随着空气燃油的混合气进入气缸，进气门关闭。
The cylinder drives a piston extraction and play materials, and by the one-way valve to control the flow of materials, the magnetic switch control cylinder stroke, which adjust the filling volume.
通过气缸带动一个活塞抽取和打出物料，并由单向阀控制物料流向，由磁环开关控制气缸行程，即调节灌装量。
The pneumatically driven LCD is designed for in-situ grinding of valve seats on large bore 2-stroke diesel engines.
这款气动驱动的LCD阀座研磨机，主要用于大孔的2冲程的柴油机上的阀座研磨使用。
Based on a proportional valve-hydraulic cylinder system, this paper puts forward the problem of implementing cushioning and positioning at any point in full-stroke by using ideal curve.
本文针对比例阀缸系统，提出了用理想曲线实现液压缸的全行程任意点的缓冲定位问题。
It introduces some advanced technologies which increase the charging efficiency, such as the variable length of the intake duct, the variable valve stroke, the variable valve timing and so on.
介绍了可变进气道长度、可变气门升程及可变气门定时等提高充气效率的先进技术。
The disc's shutoff stroke is very short and under the effect of the spring, the valve can close quickly and prevent the big noise from water-hammering.
由于阀瓣的关闭行程缩短及弹簧作用可加速关闭效果，减少水锤及水击声。
It can be concluded that cavitation of hydraulic cartridge cone valve is reduced by increasing the opening stroke and the outlet pressure and changing the geometrical structure of valve spool.
研究表明：增大阀口开度，增大出口压力，并对阀芯结构进行修改后，插装型液压锥阀阀口气穴现象均可有效减弱。
In summing up the experience of failure on the basis of the oil when the manual again, open the exhaust valve to promote the stroke from the pressure chamber filled with a symbol of stability.
在总结失败经验的基础上，再次手动注油时，打开排气阀，以推进腔排出冲程压力稳定为充满的标志。
Hydraulic circuit controlled by proportional valve. The clamping and injection stroke are controlled by potentiometer. Microprocessor can save up to 46 sets of mould date.
油压回路采用比例式电磁阀(全比例)控制，电控采用微电脑控制射出、关模，行程采用数位尺控制，能记忆46组模具资料。
The intake stroke starts with the pistonat the top of the cylinder (intake valve open and exhaust valve closed) and stops with the pistonat the bottom of its travel.
进气冲程在活塞位与气缸顶部（进气门开启，排气门关闭）时开始，在活塞到达其行程的底部时结束。
The intake stroke starts with the pistonat the top of the cylinder (intake valve open and exhaust valve closed) and stops with the pistonat the bottom of its travel.
进气冲程在活塞位与气缸顶部（进气门开启，排气门关闭）时开始，在活塞到达其行程的底部时结束。
应用推荐