For the plates with finite dimensions, the finite element method is used to obtain the stress distribution and stress concentration around the ovaloid opening.
对于有限尺寸板内开孔的情形，文中用有限单元法来分析腰圆形孔口的应力分布和应力集中。
After a cell is broken, the stress adjustments of the other cells in the system are obtained by finite element method using the broken cell as inner boundary.
当单元破裂后，将破裂单元作为内部边界，利用有限元方法计算由于这个单元破裂对系统其他单元造成的应力调整。
Simulating the deformation of the steel plate by induction heating in Finite Element Method(FEM), including temperature analysis, stress analysis and deformation analysis.
对钢板感应加热成型进行有限元分析，包括钢板截面的温度分析，应力分析，变形分析等。
This finite element method is employed to analyze the behavior of eccentrically loaded CFST columns, taking initial stress degree, slenderness ratio, and eccentric ratio as the parameters.
应用该方法，以长细比、偏心率和初应力度为主要参数对有初应力的钢管混凝土偏压构件进行了受力性能分析。
The stress and deformation of crankshaft are calculated by finite element method with six load boundary conditions and three displacement boundary conditions.
分别采用六种载荷边界条件和三种位移边界条件对曲轴应力和变形进行了有限元分析；
With the welding spot fatigue lifetime pre-estimation method, by combination of the finite element analysis and stress calculation, the welding spot fatigue damage under actual load can be calculated.
采用焊点疲劳寿命预估方法，通过有限元分析并结合应力计算，即可计算出实际载荷工况下的焊点疲劳损伤。
Possibility and efficiency in the application of this method to large finite element analysis are illustrated by an example of the stress analysis for a section of a cable stayed bridge.
以斜拉桥桥段的应力分析为例，说明在大型有限元分析中采用分阶段计算方法的可能性和有效性。
In this master thesis, the stress-strain relationships of thin films were measured by nanoindentation combined with dimensional analysis and finite element method.
本文以纳米压痕法结合量纲分析及有限元方法来测量薄膜材料的应力-应变关系。
The finite element method was used for analysis of heat stress in chip on board(COB).
本文采用有限元法分析了板上芯片（COB）的热应力分布。
The finite element method was used for analysis of heat stress in chip on board (COB).
本文采用有限元法分析了板上芯片(COB)的热应力分布。
The method of analyzing the tissue stress with finite element method plays a vital role in tissue engineering.
利用有限单元法进行组织工程中的组织应力分析具有重要意义。
The finite element method is used to analyze the relationship between strength and stress of the particle reinforced iron matrix composites and the shapes, sizes and fraction volume of the particles.
采用有限元方法分析了颗粒增强铁基复合材料强度和应力与颗粒形状、尺寸以及体积分数的关系。
In this paper, the interlaminar stress distributions of symmetric composite laminates with a hole are predicted by the three-dimensional elastoplastic finite element method.
本文用三维弹塑性有限元法计算了含圆孔对称复合材料层板的层间应力分布。
The paper presents the research into the stress state of roller teeth using FEM (finite element method). The results show that different structure parameter causes a change in roll stress.
采用有限单元法对轧辊辊齿的应力状态进行了研究，得出了不同结构参数对轧辊应力变化的影响。
Fortunately in some degree this kind of stress convergence can be eliminated or reduced to a lower level processed with the finite element equivalent stress method.
有限单元法进行拱坝分析具有诸多方面的优点，但存在较大的应力集中，而经等效应力法处理可在一定程度上削除这种应力集中的影响。
The thermal stress distribution of the stainless steel lined composite steel pipe prepared by centrifugal-SHS process was calculated by the finite element method under thermoelastic assumption.
用有限元方法计算了铝热离心法制备不锈钢内衬复合钢管过程中的残余热应力分布。
Firstly, after depicting the singularity of stress field at the top of crack, the finite element method to calculate stress intensity factor of plain fracture problems is founded.
首先，对反射裂缝尖端应力场的奇异性进行了描述，建立了平面断裂问题应力强度因子的有限单元解。
Stress of al motorcycle wheel under the service condition was analyzed with finite element method (FEM).
用有限元法对服役状态的摩托车铝合金轮毂进行了应力分析。
The finite element method is used to calculate and analyze the stress and the displacement of host rock when the openings is under the jet grouting support.
采用有限单元法对巷道注浆支护时的围岩应力和位移进行了计算分析。
With the non-line finite element method, the numberical value calculation on the stress and deformation of surrounding rock of deep mine roadways has been presented.
采用非线性有限元法，对深井巷道围岩应力及变形状态进行了数值计算。
The finite element method is used to study the internal stress distribution condition of the KE495 engine crankshaft, then the unreasonable design of the original crankshaft is known.
利用有限元法分析KE495发动机曲轴的内部应力分布状态，得出原曲轴结构的不合理之处。
Conclusion in the research and analysis of the tooth stress, the finite-element method is simple, effective, safe and reliable.
结论采用有限元法分析牙齿各部位的应力情况，是一种简捷、有效、可靠且安全的方法。
Introducing heat exchange theory and finite element theory, and deducing the theory that applies finite element method to thermal analysis and thermal stress analysis.
介绍了传热学基本理论知识，有限元方法思想。对有限元法在热分析和热应力分析中的具体应用进行了理论推导。
In this paper, temperature and stress field on the bottom had been simulated using finite element method.
本文运用有限单元法，对钢包底的温度场和应力场进行了数值模拟。
Finite element method is used to study stress and place moving field inside the structure and electric measure method is utilized to verify the result of calculation.
利用有限元方法对该结构内部的应力场和位移场进行了研究。
Three dimension finite element method is used to calculate the stress state of the cantilever during each construction stage.
因此对桥悬臂施工过程进行了三维有限元计算，分析了各个施工阶段的应力状态。
By finite element method, the distributions of additional stress of piled raft foundations in different raft rigidities are analyzed.
采用有限单元法对不同筏板刚度下桩筏基础下卧层附加应力的分布规律进行分析。
In this paper the release coefficient of residual stress of blind holes is calculated by using finite element method.
本文采用有限无法对盲孔残余应力释放测量中所需的应力释放系数进行了计算。
In this paper the release coefficient of residual stress of blind holes is calculated by using finite element method.
本文采用有限无法对盲孔残余应力释放测量中所需的应力释放系数进行了计算。
应用推荐