We ran finite element analysis stress calculations to determine where the frame needed to be reinforced for maximum strength and stiffness, then reinforced those areas with additional carbon fiber.
我们跑应力有限元分析计算，确定了框架需要得到加强的最大强度和刚度，然后加强这些领域更多的碳纤维。
The Nonlinear Finite Element Analysis was applied to study the stress and modal of an air spring, which is composed of composites with multiple orthotropic materials.
运用非线性有限元分析技术，对由多层正交各向异性复合材料组成的某型空气弹簧进行了应力和模态分析。
With the welding spot fatigue lifetime pre-estimation method, by combination of the finite element analysis and stress calculation, the welding spot fatigue damage under actual load can be calculated.
采用焊点疲劳寿命预估方法，通过有限元分析并结合应力计算，即可计算出实际载荷工况下的焊点疲劳损伤。
According to the trial, we use finite element analysis program to conduct temperature field and thermal stress analysis of the pier under sunshine, and compared the outcome with experimental results.
根据试验采用有限元分析程序，进行日照作用下桥墩的温度场和温度应力分析，并与实验结果进行对比。
The finite element method was used for analysis of heat stress in chip on board(COB).
本文采用有限元法分析了板上芯片（COB）的热应力分布。
The finite element method was used for analysis of heat stress in chip on board (COB).
本文采用有限元法分析了板上芯片(COB)的热应力分布。
In this master thesis, the stress-strain relationships of thin films were measured by nanoindentation combined with dimensional analysis and finite element method.
本文以纳米压痕法结合量纲分析及有限元方法来测量薄膜材料的应力-应变关系。
Possibility and efficiency in the application of this method to large finite element analysis are illustrated by an example of the stress analysis for a section of a cable stayed bridge.
以斜拉桥桥段的应力分析为例，说明在大型有限元分析中采用分阶段计算方法的可能性和有效性。
The stress distribution can be got by the analysis of Finite Element Method, then judging whether the material has failed by the failure criteria of composite material.
通过有限元分析，计算出了受力情况最恶劣时的响应，得出了应力分布情况，并根据复合材料强度理论判断其强度是否满足条件。
By analysis of the middle section stress of the hollow slab in the two situations of consider contact and not consider contact, verified the accuracy of contact finite element model in that situation.
通过考虑接触与不考虑接触两种情况时桥面板跨中截面的受力分析，验证该问题中接触有限元模型的正确性。
Under the condition of three kinds of nonlinearity the stress and strain distribution of the road wheel is calculated with finite element analysis software ANSYS.
建立了负重轮的三种三维有限元力学模型，在考虑三重非线性的情况下，用ANSYS有限元分析软件计算了负重轮的应力应变分布。
Simulating the deformation of the steel plate by induction heating in Finite Element Method(FEM), including temperature analysis, stress analysis and deformation analysis.
对钢板感应加热成型进行有限元分析，包括钢板截面的温度分析，应力分析，变形分析等。
The driving wheel's axle is a key parts of the billet transport vehicle, so the axle's stress and deformation were analysed by the structure finite element analysis software ANSYS.
主动车轮轴是钢坯运输车的关键零部件，采用结构有限元分析软件ANSYS分析了该轴的应力和变形。
The finite element analysis showed that the normal stress distribution of the grillage wall was about the same as that of the solid wall.
有限元计算表明，网格墙在轴力和水平力作用下的正应力分布与实体墙总体上一致；
This paper is based on stress analysis of directionally solidified turbine blade with the Finite Element Method. The reliability analysis method with a simple failure model is proposed.
本文在正交异性材料定向结晶涡轮叶片的应力有限元分析的基础上，以一种简单的破坏模式列出了可靠度的计算方法。
Conclusion in the research and analysis of the tooth stress, the finite-element method is simple, effective, safe and reliable.
结论采用有限元法分析牙齿各部位的应力情况，是一种简捷、有效、可靠且安全的方法。
Three-dimensional finite element analysis of the stress of the mandible premolar under loading on its traumatic occlusal spots.
下颌前磨牙创伤咬合点加载的三维有限元应力分析。
Introducing heat exchange theory and finite element theory, and deducing the theory that applies finite element method to thermal analysis and thermal stress analysis.
介绍了传热学基本理论知识，有限元方法思想。对有限元法在热分析和热应力分析中的具体应用进行了理论推导。
Finite element analysis method is an effective method for calculating thermal stress, but the temperature parameters for calculation have no uniform standard.
有限元是计算温度应力的很好方法，但是对于计算中所需的温度参数取值并没有统一的标准。
Finite element analysis shows that there are three stress concentration areas inside the bearing.
有限元分析表明，轴承内部存在三个应力集中区域。
Based on completion of wall strength calculation, then do the finite element stress analysis.
在完成管壁强度计算的基础上，进行管壁有限元应力分析。
Porous fluid pressure are also presented by using permeable mechanics method. Finite element model and stress analysis program are developed.
用有限元方法进行应力分析及设计保持井眼稳定的泥浆密度。
Analysis and comparison between the finite element analysis and experiment results for stress intensity factor, limit load, and flexibility factor were performed.
从应力系数、极限载荷和柔度系数三个方面对有限元计算结果和试验结果进行对比分析。
Analysis and comparison between the finite element analysis and experiment results for stress concentration factor, limit load, burst pressure and failure location were performed.
从应力集中系数、极限压力、爆破压力和爆破失效位置四个方面对有限元计算结果和试验结果进行对比分析。
The temperature distribution and stress distribution of blast furnace tuyere with gradient coating have been studied using finite element analysis software, comparing with uniform coating.
采用有限元分析软件研究了梯度涂层高炉风口的温度分布和应力分布，并与均匀涂层进行了比较。
The similarity between equivalent stress distribution around the holes in cylindrical shell and its plate model is shown through finite element analysis.
有限元分析表明，开孔圆柱壳与其相应的平板模型在开孔附近的等效应力分布非常相似。
A general nonlinear finite element code has been applied to thermoelastic stress analysis of directionally solidified air cooled turbine blades.
本文利用大型非线性有限元通用程序对定向凝固结晶的气冷叶片进行了热弹性分析。
Adopting finite element analysis method, the stress and deformation of gear coupling is analyzed, the cause of gear coupling failure is found, and the structure is optimized.
运用有限元分析方法，对齿轮联轴器进行应力、变形的分析，找出齿轮联轴器的失效原因并对它的结构设计进行了优化。
By using ALGOR finite element analysis system, the stress field and displacement field of deep excavation were calculated.
采用ALGOR有限元分析系统，对基坑开挖引起的应力场、位移场进行了分析计算。
This machine adopts steel plate welding structure, the fuselage using the finite element analysis and design, Vibratory stress Relief of internal stress, so that body stable and reliable.
液压剪板机采用钢板焊接结构，机身采用有限元分析设计、振动时效消除内应力，使机身稳定、可靠。
应用推荐