In the analysis of the stress and deformation under dynamic loading, the inertia force and damping moment should be considered in addition to the transverse shear effect.
在分析动载荷下的应力和变形时，除考虑横向剪切效应外，还须考虑微段的惯性力和阻尼力矩。
The stress and deformation analysis for surrounding rock of tunnels is an important task in tunnels design.
隧道围岩应力和变形分析是隧道设计的重要内容。
The driving wheel's axle is a key parts of the billet transport vehicle, so the axle's stress and deformation were analysed by the structure finite element analysis software ANSYS.
主动车轮轴是钢坯运输车的关键零部件，采用结构有限元分析软件ANSYS分析了该轴的应力和变形。
Stress, deformation and stability analysis of the same cemented-rockfill dam are compared before and after optimization.
比较了优化前后坝体的应力、变形与稳定分析结果。
Computation and analysis of the cylinder block stress and deformation are conducted on a 6125q diesel engine in supercharged or cylinder diameter enlarged situation by using the finite element method.
本文应用有限元法，对6125Q型柴油机机体在增压和扩缸时的变形和应力进行了计算分析。
Adopting finite element analysis method, the stress and deformation of gear coupling is analyzed, the cause of gear coupling failure is found, and the structure is optimized.
运用有限元分析方法，对齿轮联轴器进行应力、变形的分析，找出齿轮联轴器的失效原因并对它的结构设计进行了优化。
An equivalent stress method for the structural analysis of derrick with initial deformation is offered.
为此，采用等价应力法对有初始变形的井架进行结构分析。
Design and analysis: loading combinations, section steel area calculating, earring capacity computation, section stress checking, deformation and crack width checking and so on.
设计分析：含荷载组合计算、截面配筋设计、承载能力计算、截面应力验算、变形及裂缝宽度验算等。
By computer simulation, we analysis and study the law of wall rock stress distribution, deformation, the axial force of bolt and the roof-off-strata.
通过计算机数值模拟分析研究了锚杆支护回采巷道围岩应力分布、围岩变形、锚杆轴力及顶板离层规律。
According to cause analysis of heat treatment stress and deformation, the corresponding improved measure is put forward.
通过模具热处理应力及变形的原因分析，提出相应的改善对策。
Method the Finite Element Method was employed to perform the stress analysis on this valve, which included the material nonlinearity, large deformation and the contact condition.
方法考虑材料非线性，大变形和接触条件建立有限元模型，采用有限元法进行应力分析。
This paper is studying the problems of blanket fractures arising from seepage consolidation by means of analysis for seepage and deformation and stress analysis.
本文从渗流分析和变形及应力分析讨论了由于渗透固结而发生铺盖裂缝的一些问题。
This paper stresses on the analysis of the mathematical and physical significance of the average additional stress coefficient and its merit in foundation deformation calculation.
本文着重分析了平均附加应力系数的数学物理意义及用它计算地基变形的优点。
The study presented the status of force bearing analysis on the swinging rotor of expander, and the calculation of stress and deformation was carried out on the key component-swinging rotor.
研究给出了膨胀机摆动转子进行受力分析情况，对关键部件摆动转子进行了应力与变形的计算。
MCSAP program was applied to the finite element analysis for the stress and deformation of a high-speed Gleason spiral bevel gear under centrifugal load.
使用修改移植的MCSAP有限元分析程序对某高速弧齿锥齿轮进行了离心载荷下的变形和应力的分析。
The analysis of mechanical model shows that the fracture toughness is improved by residual compressive stress of substrate surface, which resists the tensile deformation of substrate.
力学模型分析表明，基体残余压应力以抵抗基体拉伸变形的方式提高了铬层的断裂韧性；
For the construction process of twice prestressed continuous beam, the stress analysis and deformation analysis method during construction stage is provided in this paper.
根据二次预应力连续梁的施工过程，提出了施工阶段的应力和变形分析方法。
By the contact simulation analysis the applications of the general contact elements in the calculations of the tooth deformation and contact stress of gears have been investigated.
通过接触仿真分析研究了通用接触单元在轮齿变形和接触应力计算中的应用。
Through the analysis of finite element example, we can see that the stress and deformation situation of buildings has improved significantly under the action of earthquake.
通过有限元算例的分析，可以看到在地震作用下建筑物的受力状态和变形情况有所明显改善。
By means of the method of finite element analysis, and simulating the actual working status of the press, the stress and deformation value of each hinge beam part of the press were obtained.
借助有限元分析方法，模拟压机的实际工作状态，获得了压机铰链梁各零件的应力和变形值。
Adopting linear and nonlinear bearing model, this paper analyses the deformation and stress of bearing with large radius, basing on nonlinear finite element analysis method.
基于非线性有限元分析方法，采用了线性轴承模型和非线性轴承模型分析了大型四点接触球轴承的变形和受力。
Simulating the deformation of the steel plate by induction heating in Finite Element Method(FEM), including temperature analysis, stress analysis and deformation analysis.
对钢板感应加热成型进行有限元分析，包括钢板截面的温度分析，应力分析，变形分析等。
The developed method can be used in the stress analysis of mechanical parts made of rubber materials subjected to finite deformation.
其结果可用在三维有限变形下橡胶类零件的应力分析。
In the present paper, the finite deformation and stress analysis for a hyperelastic rectangular plate with a center void under a uniaxial extension is studied.
本文研究了含中心微孔的超弹性矩形板在单向拉伸时的有限变形和受力分析。
Thirdly, time-history analysis of tower under earthquake loading is studied to obtain deformation and stress of structure.
然后，对大跨越输电塔进行地震影响的时程分析，得到了大跨越输电塔的变形及应力状况。
The deformation and stress distribution of the cylinder under radial force are obtained by static structure analysis.
通过静态结构分析，得到挡轮液压缸在径向载荷作用下的变形和应力分布状况；
The magnetic lineation and magnetic foliation study of the ore area show that the magnetic fabric study can proclaim the stress field of rock deformation as the petrofabric analysis.
矿区的磁线理、磁面理等磁组构研究表明，磁组构能与岩组研究一样，解决岩石变形的应力场问题。
From them, we could solve the problems of stress analysis, deformation, stability and vibration.
由此可求解应力、变形、稳定和振动等问题。
Then a three-dimensional deformation inversion analysis is conducted by orthogonal design method and neural network to acquire the distribution rule of rock body ground stress field at various depths.
在此基础上，采用正交设计方法和神经网络进行了岩体地应力场三维变形反演分析，获得了岩体地应力场沿深度的分布规律。
After imposed harmonic load, the deformation and stress variation curves with change of frequency can be gained by harmonic analysis in ANSYS.
在模态分析的基本上，对行星齿轮施加简谐载荷，得到行星齿轮的变形和应力在容易产生共振的频率范围内的变化情况；
应用推荐