For comparison, the finite element software ANSYS is used for the discharge and stress calculation of pulsed magnets. The result obtained from ANSYS agrees well with that from PMDS.
利用ansys计算脉冲强磁体的放电过程和应力分布，并把计算结果与PMDS的结果相比较，发现二者结果吻合很好。
Calculation result is analyzed in this paper. Composition of stress and estimation of lifetime are done according to the third strength theory.
本文对计算结果进行分析，并按第三强度理论进行应力组合及寿命评估。
Tangential residual stress formula closely related to fatigue is verified. The result shows that theoretical calculation conforms to the test result.
对与疲劳寿命紧密相关的切向残余应力计算式进行了试验验证，结果表明：理论计算与试验结果基本符合；
The internal stress of the joined materials was only several MPa according to the result of calculation.
应力计算结果得出焊接件中只有数兆帕的拉应力。
The result of calculation indicates the value of circumferential stress is higher than any other stress in the whole body.
计算结果表明槽内部环向应力值大于其它任何部位、任一向的应力值。
The comparison between the calculation results and test result indicates that this method can effectively predicate dynamic stress of oil tank add-on parts.
计算结果与试验结果对比表明，该方法可有效预测油箱托挂件上的动态应力。
This means that if the different forms of cable is ignored, it would bring a large deviation during the static calculation and result in the possibility that the structural stress run over the limit.
这就意味着在进行静力计算时，如果忽略了不同形式拉索的风荷载差异，会对计算结果带来较大的偏差，存在着结构应力超限的可能。
Finite element method is used to study stress and place moving field inside the structure and electric measure method is utilized to verify the result of calculation.
利用有限元方法对该结构内部的应力场和位移场进行了研究。
Calculation of brake bottom of drum brake by use finite element method for stress. according to calculating result, studied that stress is distributed over brake bottom.
对汽车鼓式双向自增力式制动器底板进行了有限元计算，在此基础上对制动器底板的应力分布进行了分析研究。
This method is applied in the calculation of the stress in the Kuqa piedmont compressive area of the Tarim basin. The calculated result coincides with the result of the acoustic experiment.
应用该方法对塔里木盆地库车山前挤压应力区进行了实际计算，其结果与实验结果相符。
The result shows that the Finite Element Analysis is an effective method for stress and displacement analysis, which should be used to replace the traditional Two-Time Calculation met…
分析计算结果表明，有限元法是进行叶轮应力和变形分析以及对叶轮进行改型设计的有效手段。
Secondly real models of the mesh unit and the whole mesh antenna are created, then shaping stress according calculation result is pressed on, finally the shaped mesh reflector antenna is obtained.
其次自己动手制作了天线单元和整体的实物模型，按照前面计算出的结果对天线网面施加预应力，得到成型后的实物索网反射面天线。
By comparing the calculation result with the field measured value, effective stress iterative method is verified to be simple and practical and can be used in pile foundation design.
通过对试算结果与实测结果的对比，说明有效应力迭代算法是一种简单实用的方法，可用于指导桩基础的设计。
The result of max equivalent stress is smaller than the results of single calculation.
这个结果与前期有限元分析结论是一致的。
The result of max equivalent stress is smaller than the results of single calculation.
这个结果与前期有限元分析结论是一致的。
应用推荐